You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
Motor wizard settings by ESCam on Thu, 2018-11-08 22:49 |
8 |
by dtp Mon, 2023-11-20 00:49 |
VESC Tool | |
|
Detection failed. Reason: Sensor detection failed by Lilian_CASTEL on Tue, 2020-11-24 11:31 |
8 |
by electricfox Thu, 2023-02-16 15:57 |
VESC Tool | |
|
I need help designing 200v 80a vesc by qwerasdf on Mon, 2021-05-03 17:08 |
8 |
by dylanu Thu, 2022-04-14 06:29 |
Third Party Hardware | |
|
Vesc 75/300 burned by electricfox on Sat, 2020-02-15 22:35 |
8 |
by pf26 Fri, 2020-03-06 09:49 |
VESC Original Hardware | |
|
Probably first dead VESC SIX by Squad on Tue, 2017-06-27 14:00 |
8 |
by frank Thu, 2017-08-17 22:31 |
VESC6 Beta | |
|
Flux linkage observer @ low speed by soltesz on Sun, 2017-12-17 16:33 |
9 |
by benjamin Thu, 2017-12-21 10:17 |
VESC Firmware | |
|
FAULT_CODE_HIGH_OFFSET_CURRENT_SENSOR_3 by TB_Poule on Sat, 2021-04-10 17:26 |
9 |
by bayetan Thu, 2023-09-21 16:24 |
General discussion | |
|
Motor braking - shorting phases by rok340 on Thu, 2021-01-21 07:49 |
9 |
by dpeinado Mon, 2022-02-14 12:36 |
General discussion | |
|
Braking in speed PID controlled mode by vadimz on Sat, 2018-09-15 14:19 |
9 |
by zybyxutese Mon, 2019-04-01 13:35 |
General discussion | |
|
vesc tool 1.25 not opening. by osis on Tue, 2019-10-29 20:50 |
9 |
by flyingbrike Wed, 2021-09-08 09:06 |
VESC Tool | |
|
15S support (and more amps) by Torxed on Mon, 2018-07-16 12:06 |
9 |
by Torxed Sat, 2018-07-21 21:52 |
Feature Requests | |
|
Invert motor direction. by Sanjoy on Thu, 2017-06-15 23:31 |
9 |
by Roger Wolff Mon, 2017-06-19 16:00 |
VESC6 Beta | |
|
FAULT_CODE_UNDER_VOLTAGE by alexantosh on Mon, 2021-11-29 09:26 |
9 |
by heravinluca Thu, 2022-08-04 04:19 |
VESC Tool | |
|
Acceleration control to desired RPM by bjohns on Fri, 2018-07-20 22:08 |
9 |
by arvidb Thu, 2018-08-09 21:15 |
General discussion | |
|
VESC Tool wont start by w31x on Wed, 2020-03-11 19:30 |
9 |
by SUB13 Sun, 2024-02-11 14:43 |
VESC Tool | |
|
ERPM to Rpm by faheemift on Wed, 2021-03-31 11:11 |
9 |
by faheemift Wed, 2021-04-14 13:01 |
General discussion | |
|
Setting PI / PID controllers in VESC for very low speeds. For CNC by K@RLSON on Sat, 2020-01-25 21:06 |
9 |
by Luke264 Wed, 2021-02-17 18:52 |
General discussion | |
|
Failure in Motor Set Up by Toshi Sharma on Tue, 2022-01-11 15:19 |
9 |
by frank Thu, 2022-01-13 14:15 |
General discussion | |
|
Help is there an issue with my new Vesc 6 by avis on Sat, 2017-09-30 15:21 |
9 |
by frank Wed, 2017-10-04 17:10 |
General discussion | |
|
highest battery current with 6.6? by devin on Tue, 2020-01-14 16:05 |
9 |
by devin Wed, 2020-01-15 01:05 |
General discussion |
Pages
