You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
Why does the 75/300 have VCC at 3.4V? by TechAUmNu on Tue, 2020-03-31 14:01 |
3 |
by TechAUmNu Wed, 2020-09-02 12:04 |
VESC Original Hardware | |
|
Flipsky 4.12 Vesc in FOC mode? by Jonny254 on Sat, 2018-09-08 11:25 |
3 |
by Jonny254 Thu, 2018-09-13 05:48 |
Third Party Hardware | |
|
Vesc can't connect to vesc tool by Roansky1 on Sat, 2022-04-30 13:05 |
3 |
by frank Tue, 2022-05-03 20:52 |
VESC Tool | |
|
Lanyard kill switch by craig w on Mon, 2022-01-03 09:30 |
3 |
by ewakegermanyhq Wed, 2022-08-03 16:55 |
General discussion | |
|
How Can I make the tool work with FW 3.5 instead of just 3.58? by ipbyrne on Fri, 2019-07-26 18:20 |
3 |
by frank Wed, 2019-08-14 14:01 |
VESC Tool | |
|
VESC 75/300 Frying in BLDC Regen by ezonca on Fri, 2020-10-23 21:53 |
3 |
by TechAUmNu Thu, 2020-10-29 13:43 |
VESC Original Hardware | |
|
Position issue by Davideo on Tue, 2017-09-19 16:48 |
3 |
by bOneWheel Mon, 2023-10-30 15:07 |
VESC Tool | |
|
Help with COMM_GET_VALUES over nRF by futuredesign on Sat, 2017-09-09 17:00 |
3 |
by futuredesign Mon, 2017-09-11 18:45 |
VESC6 Beta | |
|
Flipsky ESC 6.6 - How to Compile? [fixed] by hoeken on Tue, 2021-08-31 03:33 |
3 |
by alexantosh Wed, 2021-12-01 18:55 |
VESC Firmware | |
|
Setup parameters for battery in VESC Tool by Ulrich on Tue, 2019-02-26 11:47 |
3 |
by Photolad61 Wed, 2019-03-27 17:26 |
VESC Tool | |
|
Vesc 6 MKIV ? by mchatain on Mon, 2020-05-04 11:43 |
3 |
by maxpla Wed, 2020-06-10 10:04 |
VESC Original Hardware | |
|
Sensorless temperature compensation by ESCam on Fri, 2018-12-14 19:38 |
3 |
by Roby_88 Sat, 2023-03-11 17:39 |
Feature Requests | |
|
vesc control with 0-5v analog input... and general motor/esc recomendation by rcjustin on Thu, 2022-03-03 03:33 |
3 |
by j.konrad Fri, 2022-03-04 01:09 |
General discussion | |
|
vesc for helicopter tail rotor / freewheel for duty cycle mode by vladimir757 on Thu, 2020-06-25 14:25 |
3 |
by skyline1970 Thu, 2021-02-04 21:38 |
VESC Tool | |
|
Able to read CAN messages from VESC but cannot write messages to CAN Bus. by willd3543 on Wed, 2023-04-05 23:49 |
3 |
by benjamin Wed, 2023-04-12 07:32 |
General discussion | |
|
How to set max input voltage to over 57 volts? by johnny5in5 on Thu, 2020-09-24 03:34 |
3 |
by TheFallen Mon, 2021-03-01 16:42 |
VESC Tool | |
|
How to control motor using VESC tool in computer at constant rpm? by vimi94 on Wed, 2019-05-01 12:56 |
3 |
by foreclosurecat Tue, 2022-12-06 22:36 |
VESC Tool | |
|
speed controller at low RPM by hagoston on Mon, 2021-03-08 13:54 |
3 |
by Elwin Sun, 2021-10-31 13:53 |
General discussion | |
|
Limp mode via CAN by totalgeek9224 on Mon, 2020-02-10 14:37 |
3 |
by A2 Wed, 2021-09-08 21:20 |
Feature Requests | |
|
How different of VESC 6 and VESC 4 by Ken_chen on Thu, 2018-05-17 18:13 |
3 |
by ripperpc Mon, 2020-05-04 07:58 |
General discussion |
Pages
