You are here
Active forum topics
Primary tabs
Topic |
Replies![]() |
Last post | Forum | |
---|---|---|---|---|
Dead VESC6 due to shot from UBEC, repair possible? by Boesila on Sat, 2018-04-14 11:35 |
9 |
by benjamin Tue, 2018-06-26 14:37 |
VESC6 Beta | |
VESC Tool Compatible With FW 3.34 by a.ceviker on Sun, 2018-07-29 11:38 |
9 |
by bitmixer Fri, 2020-02-21 22:18 |
VESC Tool | |
FAULT_CODE_ABS_OVER_CURRENT on custom pcb by TVAVAE on Sat, 2021-07-10 00:44 |
9 |
by hakan seray Wed, 2022-06-15 12:27 |
Third Party Hardware | |
Setting PI / PID controllers in VESC for very low speeds. For CNC by K@RLSON on Sat, 2020-01-25 21:06 |
9 |
by Luke264 Wed, 2021-02-17 18:52 |
General discussion | |
highest battery current with 6.6? by devin on Tue, 2020-01-14 16:05 |
9 |
by devin Wed, 2020-01-15 01:05 |
General discussion | |
(solved) Configuration smooth motordirection change by horak2084 on Mon, 2019-02-25 20:44 |
9 |
by fpagac Sat, 2020-04-25 17:17 |
VESC Firmware | |
ERPM settings restrict carving speed on outer wheel. Poor user experience. by Paul15578 on Fri, 2018-01-12 02:28 |
9 |
by Ackmaniac Tue, 2018-04-24 13:47 |
General discussion | |
Braking in speed PID controlled mode by vadimz on Sat, 2018-09-15 14:19 |
9 |
by zybyxutese Mon, 2019-04-01 13:35 |
General discussion | |
Low power VESC - any available by wdaehn on Wed, 2018-02-28 18:02 |
9 |
by TechAUmNu Mon, 2018-03-19 11:54 |
Third Party Hardware | |
Problem with Bluetooth connection (HM-10) by squdowx on Mon, 2018-07-30 15:56 |
9 |
by CTSchorsch Thu, 2019-12-05 21:27 |
General discussion | |
Noise with Hall sensor at high speed by yosoufe on Thu, 2018-03-08 12:34 |
9 |
by yosoufe Tue, 2018-03-20 09:30 |
General discussion | |
Problem with burned FETs and drivers after reconnect battery by CTSchorsch on Sat, 2021-01-16 19:49 |
9 |
by CTSchorsch Wed, 2021-02-17 13:42 |
Third Party Hardware | |
Flux linkage observer @ low speed by soltesz on Sun, 2017-12-17 16:33 |
9 |
by benjamin Thu, 2017-12-21 10:17 |
VESC Firmware | |
Problems with Initial flash of Hw4:12 by Idoff on Mon, 2018-04-16 18:47 |
9 |
by Frankfartin2077 Thu, 2019-04-04 10:10 |
VESC Firmware | |
Your input needed: FESC 4.12 / Arduino / 4X 350W motors by matukash on Tue, 2020-07-21 16:36 |
9 |
by Billie Wed, 2023-02-01 05:46 |
General discussion | |
vesc tool 1.25 not opening. by osis on Tue, 2019-10-29 20:50 |
9 |
by flyingbrike Wed, 2021-09-08 09:06 |
VESC Tool | |
Serial Connection Lost with Vesc6.6 Firmware 5.2 and Vesc Tool 3.0 by Dan Slanker on Wed, 2021-04-28 16:56 |
9 |
by AngelKillR Wed, 2022-09-28 05:10 |
General discussion | |
FAULT_CODE_UNDER_VOLTAGE by alexantosh on Mon, 2021-11-29 09:26 |
9 |
by heravinluca Thu, 2022-08-04 04:19 |
VESC Tool | |
Rough acceleration - BLDC & FOC by Loose Nickers on Tue, 2020-02-11 07:56 |
9 |
by MC_DIY_Beginner Mon, 2022-05-16 13:34 |
VESC Tool | |
VESC recommendation for sailboat conversion by Henque19 on Thu, 2019-11-28 00:42 |
9 |
by Henque19 Fri, 2019-12-20 16:15 |
General discussion |
Pages
