You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
200V +200A power stage and custom VESC controller with fault protection by ZombieSS on Sat, 2020-07-18 07:35 |
3 |
by mystamo Tue, 2020-07-28 22:07 |
Third Party Hardware | |
|
Can't access my forum post I made a few days ago by badgerthing on Wed, 2024-04-17 03:31 |
3 |
by electricfox Fri, 2024-05-10 22:12 |
General discussion | |
|
Trampa 100/250 with one old brushed DC motor....how can i change the motor spin direction????plz help!!! by Asi on Fri, 2022-11-18 12:45 |
3 |
by frank Sat, 2022-11-19 14:55 |
General discussion | |
|
Vesc can't connect to vesc tool by Roansky1 on Sat, 2022-04-30 13:05 |
3 |
by frank Tue, 2022-05-03 20:52 |
VESC Tool | |
|
Lanyard kill switch by craig w on Mon, 2022-01-03 09:30 |
3 |
by ewakegermanyhq Wed, 2022-08-03 16:55 |
General discussion | |
|
copy setup from one vesc to another? by curtm on Mon, 2019-07-08 20:33 |
3 |
by district9prawn Sat, 2019-07-20 23:44 |
Third Party Hardware | |
|
UART Accel/Gyro/Mag data by NATUITION on Sat, 2019-12-28 11:25 |
3 |
by NATUITION Tue, 2020-01-07 22:14 |
General discussion | |
|
MAYTECH ESC6 200A runs fine on 6s, faults immediately on 12s by mxpro32 on Sun, 2019-06-30 21:39 |
3 |
by TechAUmNu Tue, 2019-08-13 10:21 |
Third Party Hardware | |
|
CAN defect? 4WD - CAN does not detect anymore... HELP! by MountainBen on Tue, 2021-02-02 04:04 |
3 |
by skyline1970 Fri, 2021-02-05 19:50 |
Third Party Hardware | |
|
Upload bootloader to stm32 f405? by jneumann on Sat, 2020-08-08 07:11 |
3 |
by TechAUmNu Sat, 2020-08-08 18:29 |
General discussion | |
|
Do I need phase voltage sense? by Flepple on Mon, 2021-01-25 15:31 |
3 |
by GPereira Thu, 2022-02-10 11:43 |
General discussion | |
|
Question on throttle response by petermarcotte1 on Wed, 2020-07-29 11:28 |
3 |
by petermarcotte1 Sat, 2020-08-01 14:17 |
General discussion | |
|
Forum broken. by Roger Wolff on Thu, 2018-05-03 08:31 |
3 |
by Tilman Baumann Fri, 2018-05-04 13:01 |
General discussion | |
|
firmware V6.06 vs VESC tool V6.05 by shuang on Thu, 2024-12-05 06:49 |
3 |
by Polyloop Mon, 2025-03-31 17:34 |
VESC Firmware | |
|
Power levels by vescbeginer on Wed, 2023-08-16 22:20 |
3 |
by vadicus Wed, 2023-08-23 20:58 |
VESC Firmware | |
|
Discrepancies between VESC Tool 3.01 Motor Settings & XML config file by j.konrad on Sat, 2022-01-15 22:13 |
3 |
by benjamin Mon, 2022-02-21 22:17 |
VESC Tool | |
|
Newbie - controller/motor not working by JLow75 on Tue, 2018-11-13 09:50 |
3 |
by bsissell Fri, 2021-11-26 07:17 |
General discussion | |
|
VESC 75/300 vs VESC 100/250 by XBO on Tue, 2021-09-07 19:31 |
3 |
by flyingbrike Wed, 2021-09-08 13:42 |
General discussion | |
|
Question about COMM_GET_IMU_DATA packet by rrzaripov on Wed, 2020-03-04 00:28 |
3 |
by Addy Fri, 2020-04-24 06:49 |
VESC Tool | |
|
Built in BLE HD60 not Working by CS on Mon, 2021-08-23 13:21 |
3 |
by frank Thu, 2021-08-26 08:09 |
VESC Original Hardware |
Pages
