You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
help flashing 4.12 with new firmware by adamclarke1985 on Fri, 2020-05-01 02:23 |
2 |
by VESCTroll Fri, 2020-05-29 19:09 |
VESC Firmware | |
|
Rc controller more than one input ? by zebb.guy@moshon... on Tue, 2022-07-26 14:51 |
2 |
by zebb.guy@moshon... Wed, 2022-07-27 17:22 |
General discussion | |
|
Bootloader? by curtm on Thu, 2019-07-11 01:07 |
2 |
by curtm Fri, 2019-07-12 16:43 |
VESC Firmware | |
|
Custom code changes- I/O pin go high or low by dsuresh on Thu, 2021-05-13 19:50 |
2 |
by dsuresh Fri, 2021-05-14 22:30 |
General discussion | |
|
VESC 75 300 R2 - correct battery conection by SafrdA on Fri, 2021-04-30 13:13 |
2 |
by frank Wed, 2021-05-26 11:19 |
VESC Original Hardware | |
|
VESC UART response format? by dcode on Fri, 2023-09-01 18:58 |
2 |
by rafeh1 Fri, 2024-10-11 01:04 |
VESC Development and Beta Testing | |
|
Traction control with different motors by Ba1tuks on Sun, 2020-05-31 15:10 |
2 |
by Mansens88 Mon, 2025-02-24 01:45 |
Feature Requests | |
|
Реверс вращения двигателя by Wolod5 on Sat, 2021-01-16 09:59 |
2 |
by Wolod5 Sat, 2021-01-16 12:21 |
VESC Tool | |
|
Loud Bang at Sensor-less Switchover with hub motor by hackeybabel on Sat, 2021-08-21 11:13 |
2 |
by hackeybabel Thu, 2021-08-26 07:19 |
General discussion | |
|
Repairing by lamak on Thu, 2025-06-26 07:08 |
2 |
by ispor4en Fri, 2025-06-27 21:15 |
General discussion | |
|
Axial Flow Pump Project by design@imsltd.co.nz on Thu, 2021-12-09 02:05 |
2 |
by design@imsltd.co.nz Fri, 2021-12-10 01:51 |
General discussion | |
|
Using STM32F407 for a custom board by kapek on Mon, 2020-04-06 04:16 |
2 |
by vadicus Fri, 2020-04-10 06:31 |
General discussion | |
|
How to connect 5 Pin Hall Sensor to 6 Pin Hall Sensor Connector by tinytuna38 on Thu, 2024-06-20 20:56 |
2 |
by Nineballshot Mon, 2024-11-25 02:38 |
General discussion | |
|
Writing value to both VESCs on FocFox Unity by agraham on Wed, 2022-02-23 21:45 |
2 |
by benjamin Thu, 2022-02-24 10:57 |
VESC Tool | |
|
wanna make custom made esc and tool by Vigneshwar on Tue, 2019-11-19 13:07 |
2 |
by Hugo133 Mon, 2021-02-22 12:49 |
Third Party Hardware | |
|
VESC tool "GUI" issue. by Roger Wolff on Tue, 2018-01-02 15:13 |
2 |
by ThierryGTLTS Wed, 2018-01-10 17:38 |
VESC Tool | |
|
DIY VESC 6 "DRV" FAULT by a.dahhak on Thu, 2020-06-11 22:10 |
2 |
by a.dahhak Fri, 2020-06-12 20:06 |
General discussion | |
|
Motor Overheating in FOC by amanpereira1 on Thu, 2022-05-05 16:14 |
2 |
by Nuppen Wed, 2024-02-14 08:14 |
General discussion | |
|
CAN sends error frame by dgarciasoto on Wed, 2022-04-27 07:11 |
2 |
by fingerprintdax Thu, 2025-10-02 00:46 |
VESC Firmware | |
|
MANUAL by frank on Sat, 2017-06-10 00:29 |
2 |
by frank Wed, 2017-06-14 16:46 |
VESC6 Beta |
Pages
