You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
DIY vesc 75/300 variant power stage problem by motordriver111 on Sat, 2021-03-27 21:44 |
2 |
by vadicus Tue, 2021-04-06 18:50 |
Third Party Hardware | |
|
Can you switch censored to sensor less or HFI by diyRick on Wed, 2021-06-30 23:43 |
2 |
by drdrs Wed, 2021-07-07 07:11 |
General discussion | |
|
Can't find Configurable FOC current filter in VESC TOOL by e-biker on Sun, 2018-04-08 12:18 |
2 |
by e-biker Sun, 2018-04-08 12:55 |
General discussion | |
|
VESC tool and sk8-esc V6 set up shows incorrectcurrent usage by DominykasS on Fri, 2022-09-30 13:54 |
2 |
by Frizzaper Wed, 2023-11-15 04:25 |
VESC Tool | |
|
Problems with writing Firmware to the processor by Goex on Wed, 2018-03-28 09:11 |
2 |
by Idoff Tue, 2018-04-17 11:04 |
VESC Firmware | |
|
Charging through phase wires by jesusc on Mon, 2021-01-18 21:14 |
2 |
by jesusc Thu, 2021-06-03 02:17 |
VESC Original Hardware | |
|
Regenerate 30V to charge 40V battery by musinov on Thu, 2021-03-18 19:25 |
2 |
by vadicus Sun, 2021-04-11 19:27 |
General discussion | |
|
vesc tool not opening by RemyMade413 on Sat, 2026-02-28 12:15 |
2 |
by mariuszdymon Sat, 2026-02-28 23:07 |
VESC Tool | |
|
Is it possible to stop a motor at one exact desired location without hall sensor? by vimi94 on Thu, 2019-08-15 10:58 |
2 |
by vimi94 Tue, 2019-08-20 13:37 |
VESC Tool | |
|
PAS with variable assist+regen brake by Lukas_T on Fri, 2025-08-29 18:05 |
2 |
by Lukas_T Fri, 2025-10-31 10:28 |
General discussion | |
|
VESC 100-250 doesn't work with firmware built from 100_250 folder by aerostepa on Sat, 2021-01-30 17:14 |
2 |
by aerostepa Sun, 2021-01-31 17:42 |
VESC Firmware | |
|
cant connect via usb by curtm on Wed, 2019-06-19 03:05 |
2 |
by curtm Thu, 2019-07-04 00:37 |
VESC Tool | |
|
FOC configuration when resistance is measured as R=0. by Roger Wolff on Tue, 2018-08-28 18:20 |
2 |
by Foxyirish1987 Tue, 2020-04-07 13:12 |
VESC Tool | |
|
only Encoder with no index by Dina on Mon, 2026-06-29 10:24 |
2 |
by Dina Mon, 2026-06-29 14:20 |
General discussion | |
|
IPM/Salient Motor Tuning by SRFirefox on Wed, 2020-08-26 23:19 |
2 |
by JP Wed, 2022-08-17 11:22 |
General discussion | |
|
VESC75/300 USB Connection Issue by Gerhard on Fri, 2020-11-20 22:37 |
2 |
by Gerhard Tue, 2020-12-01 16:26 |
VESC Original Hardware | |
|
How can I add watts data to solidgeek? by Fixitmoditbreakit on Sat, 2021-06-12 00:07 |
2 |
by vadicus Tue, 2021-06-15 17:50 |
General discussion | |
|
pulsation at mid speed by smallbikefun on Sun, 2024-05-12 19:00 |
2 |
by Lizzle Wed, 2024-09-04 06:07 |
VESC Tool | |
|
VESC limits power after 15 sec by Blcd on Wed, 2024-05-01 23:11 |
2 |
by Blcd Thu, 2024-05-02 11:15 |
Projects incorporating VESC technology | |
|
VESCTOOL - Multiple VESC simultaneous configuration (Same CANBUS ID issues) by Filcas on Thu, 2021-02-18 20:52 |
2 |
by Filcas Fri, 2021-02-19 01:37 |
VESC Tool |
Pages
