You are here
Feature Requests
Log in to post new content in the forum.
Topic / Topic starter | Replies | Last post | |
---|---|---|---|
more ADC options by vufmihai » Thu, 2019-10-17 08:33 |
1 |
by Vos Fri, 2021-02-12 13:19 |
|
safety switch by Ralph Luckwaldt » Mon, 2019-10-21 13:15 |
1 |
by frank Mon, 2019-10-21 20:58 |
|
Hot swapping of controller parameters by Victor Bruun » Wed, 2020-01-29 09:22 |
1 |
by vadicus Wed, 2020-01-29 20:46 |
|
Vesc slow speed BLDC without coging by igisboard » Tue, 2018-10-09 18:38 |
1 |
by Dillon Mon, 2018-11-19 01:41 |
|
cPPM APP with mixing by Enak » Wed, 2017-09-06 00:54 |
1 |
by benjamin Wed, 2017-09-06 23:25 |
|
Read erpm of motor through motor tachometer by jordanlow » Tue, 2019-04-30 15:18 |
1 |
by Teslafly Sat, 2019-07-20 00:44 |
|
watt mode by Willoz600 » Tue, 2017-10-10 09:26 |
1 |
by frank Mon, 2017-10-16 20:58 |
|
Bring back BLDC mode!! by Tony_Stark » Sun, 2021-08-15 09:59 |
1 |
by skyline1970 Fri, 2021-10-29 12:24 |
|
PAS: constant torque control by afzalm » Thu, 2021-10-07 11:25 |
1 |
by TittyTwister Sun, 2022-07-10 12:43 |
|
Access to balance fault settings when using other apps for control. by crutch » Tue, 2022-03-22 11:14 |
1 |
by auspiciouszesty Mon, 2022-06-06 10:32 |
|
Locking for reconfiguration/reprogramming by TZTZ » Tue, 2020-05-26 19:14 |
1 |
by TZTZ Wed, 2020-05-27 16:35 |
|
benjamin, New feature please 1. Lock up Profile selection in App. with Password and add RFID reader. by justinlinh » Sat, 2020-07-11 00:08 |
1 |
by Solid_37 Sun, 2021-01-10 23:40 |
|
VESC TOOL Mobile over OTG by xvatriusx » Sat, 2022-08-13 04:25 |
1 |
by besenyeim Mon, 2023-04-24 12:26 |
|
Adding two reed contacts and adapting the software accordingly by WulfKraneis » Sun, 2020-09-06 16:25 |
1 |
by district9prawn Fri, 2020-09-11 13:15 |
|
Hard wired remote by edparadiso. » Tue, 2020-11-10 00:41 |
1 |
by district9prawn Tue, 2020-11-10 15:32 |
|
Bluetooth "ignition key" by topiaskorpi » Wed, 2019-10-16 18:47 |
1 |
by hockinsk Fri, 2019-11-01 20:14 |
|
ADC Throttle Redundancy by bgdwiepp » Mon, 2020-01-20 09:18 |
1 |
by frank Mon, 2020-01-27 20:42 |
|
Add another motor temperature sensor type (only minor tweak needed) by Henque19 » Wed, 2020-01-29 21:25 |
1 |
by Henque19 Wed, 2020-03-25 11:31 |
|
ERPM Limit Update Over CAN by josh » Sun, 2019-06-02 01:48 |
1 |
by josh Sun, 2019-06-02 02:05 |
|
Cruise control speed reduction by dsuresh » Mon, 2021-03-01 20:40 |
2 |
by dsuresh Wed, 2021-06-30 21:31 |
|
PWM encoder support by Ieton2hahw » Fri, 2021-06-18 05:47 |
2 |
by Ieton2hahw Fri, 2021-06-18 19:24 |
|
Some small problems with the VESC 6 and the VESC Tool V 0.87 by JL2579 » Thu, 2018-01-11 16:27 |
2 |
by JL2579 Tue, 2018-01-16 16:58 |
|
Motion commands for controlling CNCs by andresv » Fri, 2017-09-08 10:35 |
2 |
by brushlessjoe Sun, 2019-03-17 21:29 |
|
Support for AMC1301 powered from bootstrap by antonchromjak » Thu, 2019-04-04 22:46 |
2 |
by antonchromjak Fri, 2019-04-05 11:16 |
|
Adding a Openloop COMM Comand This topic has been moved to "General discussion" (View topic) |
Log in to post new content in the forum.