You are here

Third Party Hardware

Topic / Topic starter Replies Last postsort ascending
Normal topic Custom PCB based on 6.4
by CTSchorsch » Wed, 2019-02-20 11:49
2
by CTSchorsch
Mon, 2020-01-20 07:30
Normal topic Custom hardware
by aachner » Thu, 2019-12-19 15:15
5
by vadicus
Thu, 2020-01-16 20:28
Normal topic low voltage/power VESC
by qdxiatao » Sun, 2019-12-29 09:27
2
by qdxiatao
Mon, 2020-01-06 02:04
Normal topic Maker X Mini VESC burned at 46V. My fault or shitty quality?
by smileandbeware » Mon, 2019-11-18 10:53
3
by frank
Thu, 2019-12-26 15:27
Normal topic Motor controller commercial test benches
by lopezcontreras » Mon, 2019-12-16 15:31
0
by lopezcontreras
Mon, 2019-12-16 15:31
Normal topic New need help
by VinnyF » Tue, 2019-12-10 13:16
2
by tex
Wed, 2019-12-11 17:19
Normal topic Vesc 6.6 120a ADC2 pin out seems to be shorting..?
by beetbocks » Tue, 2019-11-26 14:23
1
by frank
Thu, 2019-12-05 11:25
Normal topic Can't update firmware FSESC 4.12
by TimBilliet » Tue, 2019-11-26 21:52
1
by TechAUmNu
Wed, 2019-11-27 14:47
Normal topic Flipsky VESC-clone firmware udapte problems
by gui-rider » Sun, 2019-04-28 22:39
4
by avsha
Fri, 2019-11-22 06:55
Normal topic Abi encoder??
by Vigneshwar » Wed, 2019-11-20 06:10
0
by Vigneshwar
Wed, 2019-11-20 06:10
Normal topic I can't communicate with the VESC-Clone
by Savavit » Sun, 2019-10-27 17:42
1
by vadicus
Thu, 2019-11-07 06:48
Normal topic VESC with 3 shunt
by _johnny_ » Fri, 2019-11-01 18:57
0
by _johnny_
Fri, 2019-11-01 18:57
Normal topic VESC hw_60 invert PWM.
by _johnny_ » Fri, 2019-11-01 18:44
0
by _johnny_
Fri, 2019-11-01 18:47
Normal topic EBESC 6.1 Remote wont connect and cant get past the error code port not recognized
by flashg69777 » Tue, 2019-10-22 02:01
1
by frank
Tue, 2019-10-22 11:13
Normal topic IGBT Vesc FOC not working
by ziumus » Sat, 2019-09-28 15:48
9
by bgdwiepp
Sat, 2019-10-19 21:56
Normal topic SpaceVESC, a modular small VESC
by SpaceVESCproject » Wed, 2019-10-02 21:35
2
by frank
Thu, 2019-10-17 11:47
Normal topic VESC Design - Review and Bringup - 150V - 20A
by ripperpc » Sat, 2019-09-21 17:30
1
by TechAUmNu
Mon, 2019-09-30 14:34
Normal topic Flipsky VESC 50A
by CraigL100 » Fri, 2019-08-30 16:57
5
by CraigL100
Sat, 2019-09-14 12:10
Normal topic Motor not spinning NO FAULTS
by 123seaborder » Mon, 2019-06-10 21:46
1
by gogglespast
Sat, 2019-09-14 08:34
Normal topic Flipsky FSVESC Bricked?
by dan.rowe » Thu, 2019-09-12 19:45
0
by dan.rowe
Thu, 2019-09-12 19:45
Normal topic ESC ceases operation after 40 sec ride
by dekafive » Sun, 2019-08-25 22:25
1
by frank
Mon, 2019-09-02 10:50
Normal topic MAYTECH ESC6 200A runs fine on 6s, faults immediately on 12s
by mxpro32 » Sun, 2019-06-30 21:39
3
by TechAUmNu
Tue, 2019-08-13 10:21
Normal topic MINI FOC from MakerX
by YUTW » Thu, 2019-08-08 11:17
1
by speed3r
Tue, 2019-08-13 10:17
Normal topic Maytech 200A does not work in FOC, will a A200S work better?
by doom » Wed, 2019-08-07 20:40
1
by TechAUmNu
Fri, 2019-08-09 21:01
Normal topic Hooking up two or more motor drivers to the same MCU
by darkclaude » Thu, 2019-06-20 10:02
4
by skyline1970
Wed, 2019-07-31 13:53
New posts
No new posts
Hot topic with new posts
Hot topic without new posts
Sticky topic
Locked topic
Subscribe to RSS - Third Party Hardware