You are here
Third Party Hardware
Log in to post new content in the forum.
Topic / Topic starter |
Replies | Last post | |
|---|---|---|---|
|
How to change the Phase PWM polarity by Boben » Fri, 2021-04-02 20:51 |
0 |
by Boben Fri, 2021-04-02 20:51 |
|
|
How to fix VESC killed by over current in serial comm? by 8bit » Sun, 2021-05-16 04:02 |
8 |
by vadicus Fri, 2023-01-13 19:15 |
|
|
How to start a new VESC 6 hardware project by olek130 » Sun, 2021-08-15 18:10 |
1 |
by vadicus Sun, 2021-08-22 04:31 |
|
|
How to upload firmware on MINI4 ? by john » Mon, 2018-11-12 10:55 |
1 |
by john Mon, 2018-11-12 11:59 |
|
|
Hub Motor Setup Issues by iss_aerospace » Sun, 2024-09-29 20:12 |
1 |
by electricfox Sun, 2024-09-29 20:31 |
|
|
HW advice : repair , vesc 4.12, vesc 6.4 or better wait ? by frameto » Sun, 2017-11-19 21:36 |
1 |
by josh Thu, 2018-07-26 18:47 |
|
|
HW4.12 Firmware trouble by CTSchorsch » Wed, 2018-12-05 21:09 |
4 |
by sam.vanratt Fri, 2018-12-28 17:55 |
|
|
Hyper-V No "New" button in the action pane by Gheer » Tue, 2020-11-17 13:02 |
0 |
by Gheer Tue, 2020-11-17 13:02 |
|
|
I can't communicate with the VESC-Clone by Savavit » Sun, 2019-10-27 17:42 |
1 |
by vadicus Thu, 2019-11-07 06:48 |
|
|
I can't get my fresc to work I think all the leds are lighting up but when I pull the trigger on the remote nothing happens by pdxcjc » Fri, 2022-03-11 17:46 |
5 |
by Gatze Mon, 2022-05-09 17:03 |
|
|
I need help designing 200v 80a vesc by qwerasdf » Mon, 2021-05-03 17:08 |
8 |
by dylanu Thu, 2022-04-14 06:29 |
|
|
I Need Some Guidance With My Schematic 16s 50a by qwerasdf » Sat, 2022-01-01 15:04 |
6 |
by mckenzie.keith Fri, 2022-01-14 04:39 |
|
|
IGBT Vesc FOC not working by ziumus » Sat, 2019-09-28 15:48 |
9 |
by bgdwiepp Sat, 2019-10-19 21:56 |
|
|
INA240A1 replacement by CTSchorsch » Thu, 2021-11-11 15:50 |
3 |
by skyline1970 Sat, 2021-11-13 11:37 |
|
|
Incorrect R and L detection? by vadicus » Mon, 2019-11-04 20:49 |
11 |
by vadicus Fri, 2020-02-28 00:21 |
|
|
Inductance measurement ? by ziumus » Sat, 2019-05-25 21:31 |
3 |
by a.dahhak Wed, 2020-06-03 21:48 |
|
|
Information about "Das RS" and "Das mini" hardware using DRV8313/DRV8320 by hexakopter » Thu, 2018-04-26 19:18 |
3 |
by hexakopter Wed, 2018-06-13 00:39 |
|
|
Is it possible to run VESC software on a STM32G431? by WackoKacko » Mon, 2023-02-06 11:52 |
2 |
by Svein Utne Tue, 2023-03-07 13:58 |
|
|
Is my custom motor inductance too low? by perpetum » Wed, 2020-11-04 18:01 |
2 |
by perpetum Sat, 2020-11-28 18:28 |
|
|
Is there a way to deactivate roll to start function FW 5.02 by Philo » Sun, 2021-04-11 13:55 |
0 |
by Philo Sun, 2021-04-11 13:58 |
|
|
Issue with my Bluetooth connection on VESC by Tom E » Mon, 2025-10-13 07:42 |
1 |
by Tom E Mon, 2025-10-13 08:21 |
|
|
Issues flashing VESC HW 4.12 by Nic_cfar » Wed, 2020-10-21 00:08 |
1 |
by xeniter Mon, 2021-09-13 22:33 |
|
|
Issues with UART Connection: VESC 6.05 and ESP32 Display by PHNTM » Mon, 2024-10-14 18:23 |
0 |
by PHNTM Mon, 2024-10-14 23:23 |
|
|
Lack of throttle control / too fast by mgisch » Mon, 2019-04-01 05:57 |
6 |
by mgisch Wed, 2019-04-03 09:53 |
|
|
Look at my amazing BLDC, see something weird? (help plz) by javivi » Thu, 2020-02-06 16:19 |
4 |
by roelth Sun, 2020-02-23 20:01 |
Log in to post new content in the forum.
