You are here
Third Party Hardware
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Flipsky FSESC75450 ABI encoder setup by CheatingBoy6890 » Fri, 2026-03-20 20:23 |
1 |
by CheatingBoy6890 Fri, 2026-03-27 20:02 |
|
|
Alternate method to program Makerbase MKSESC75200 by Zachary Levenberg » Sat, 2024-02-10 23:22 |
1 |
by Ganzey Mon, 2024-02-12 02:55 |
|
|
Blew a FSESC 75350 on a sur-ron, don't know why by vescerBoii » Fri, 2024-03-15 18:51 |
1 |
by iv.kravchenko Fri, 2024-09-27 21:06 |
|
|
Reverse button does not reverse, just slow down on Flipsky 75100 by artsin » Sat, 2024-06-22 22:19 |
1 |
by artsin Tue, 2024-06-25 00:07 |
|
|
Why only 1000 phase amp limit, and field weakening amp limits by fart » Wed, 2024-08-28 05:18 |
1 |
by electricfox Wed, 2024-08-28 13:40 |
|
|
Hub Motor Setup Issues by iss_aerospace » Sun, 2024-09-29 20:12 |
1 |
by electricfox Sun, 2024-09-29 20:31 |
|
|
Makerbase VESC 84200HP It won't turn on. by Deejii23 » Sun, 2024-11-24 16:31 |
1 |
by Deejii23 Thu, 2024-11-28 18:58 |
|
|
3 shunt low side resistor configuration based on VESC 6 by jordanlow » Thu, 2019-02-14 16:42 |
1 |
by TechAUmNu Thu, 2019-02-14 18:31 |
|
|
84v VESC?? by larsrocket » Sun, 2018-04-01 22:41 |
1 |
by larsrocket Mon, 2018-04-30 19:59 |
|
|
Maytech VESC duty cycle & PID control problems by subodh.malgonde » Mon, 2018-10-01 11:49 |
1 |
by subodh.malgonde Tue, 2018-10-02 11:59 |
|
|
SPI encoder on MIN4 by john » Wed, 2018-11-14 11:31 |
1 |
by F4metz Sat, 2019-03-02 14:18 |
|
|
maytech mto91hbm-nh motors hal sensor by nolander » Thu, 2019-01-10 00:01 |
1 |
by sunsam8 Thu, 2019-01-10 11:15 |
|
|
Gate driver by RSR » Sat, 2019-01-26 21:46 |
1 |
by bgdwiepp Fri, 2019-03-01 15:21 |
|
|
Maytech VESC 6 FOC turn off without fault at high erpm, blower by gabrield » Fri, 2020-05-15 01:16 |
2 |
by ImperialSB Thu, 2021-04-22 17:54 |
|
|
Sailboat Controller/Motor/Generator by Joe Lorkovic » Thu, 2020-05-28 21:55 |
2 |
by Eric Crouch Sat, 2020-06-06 19:11 |
|
|
SpaceVESC, a modular small VESC by SpaceVESCproject » Wed, 2019-10-02 21:35 |
2 |
by frank Thu, 2019-10-17 11:47 |
|
|
New need help by VinnyF » Tue, 2019-12-10 13:16 |
2 |
by tex Wed, 2019-12-11 17:19 |
|
|
Vx1 controller help by stefann » Wed, 2020-03-11 12:42 |
2 |
by stefann Sun, 2020-03-15 00:36 |
|
|
FSESC running rough recently by oger » Sat, 2022-06-25 15:35 |
2 |
by oger Thu, 2022-07-21 21:07 |
|
|
Can't connect my FSESC through USB by digo_bob » Tue, 2022-01-11 04:31 |
2 |
by Ganzey Tue, 2022-12-27 19:51 |
|
|
xESC2 mini - a small, low power VESC derivative for robotics use by clemens.elflein » Fri, 2022-03-04 14:44 |
2 |
by Mowman Fri, 2023-06-30 22:51 |
|
|
USB Design and connection issues by brieru » Sun, 2022-03-20 00:45 |
2 |
by brieru Wed, 2022-03-30 00:50 |
|
|
compatability assistance by NRGFPV » Mon, 2020-12-28 04:58 |
2 |
by NRGFPV Wed, 2020-12-30 08:46 |
|
|
Connect PixHawk 4 to FSESC 4.12 by iwdok » Tue, 2021-10-19 11:18 |
2 |
by frank Wed, 2021-12-01 13:38 |
|
|
Firmware flash on new born board by matrixgti » Thu, 2020-10-08 20:39 |
2 |
by TechAUmNu Tue, 2020-10-13 10:18 |
Log in to post new content in the forum.
