You are here
Third Party Hardware
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
What about using the Votol em150 3kw 48-72v? by Arpanx » Sat, 2020-03-21 11:23 |
1 |
by vadicus Mon, 2020-03-23 20:15 |
|
|
Maytech 200A does not work in FOC, will a A200S work better? by doom » Wed, 2019-08-07 20:40 |
1 |
by TechAUmNu Fri, 2019-08-09 21:01 |
|
|
VESC Design - Review and Bringup - 150V - 20A by ripperpc » Sat, 2019-09-21 17:30 |
1 |
by TechAUmNu Mon, 2019-09-30 14:34 |
|
|
I can't communicate with the VESC-Clone by Savavit » Sun, 2019-10-27 17:42 |
1 |
by vadicus Thu, 2019-11-07 06:48 |
|
|
Why only 1000 phase amp limit, and field weakening amp limits by fart » Wed, 2024-08-28 05:18 |
1 |
by electricfox Wed, 2024-08-28 13:40 |
|
|
Hub Motor Setup Issues by iss_aerospace » Sun, 2024-09-29 20:12 |
1 |
by electricfox Sun, 2024-09-29 20:31 |
|
|
config wanted, for 75100 with ebike geared hub motor by tom355 » Mon, 2023-02-20 09:51 |
1 |
by Oded Mazor Fri, 2023-02-24 15:08 |
|
|
Cheap Focer Troubleshoot DRV by Niklas Probst » Mon, 2023-03-13 08:22 |
1 |
by Niklas Probst Mon, 2023-03-13 12:54 |
|
|
VESC 75/300 half bridge burns out when I switch to FOC mode by vajasgeri » Thu, 2023-05-04 14:02 |
1 |
by vadicus Fri, 2023-05-05 19:40 |
|
|
MINI 4 having DRV8301 in mini4.h ! by snakeplissken » Fri, 2023-11-24 20:58 |
1 |
by justlovescience Tue, 2024-02-06 16:36 |
|
|
Alternate method to program Makerbase MKSESC75200 by Zachary Levenberg » Sat, 2024-02-10 23:22 |
1 |
by Ganzey Mon, 2024-02-12 02:55 |
|
|
Blew a FSESC 75350 on a sur-ron, don't know why by vescerBoii » Fri, 2024-03-15 18:51 |
1 |
by iv.kravchenko Fri, 2024-09-27 21:06 |
|
|
wrong amps reading (realtime data) by flez1966 » Wed, 2024-03-27 13:55 |
1 |
by TheFox Mon, 2024-04-01 22:15 |
|
|
Reverse button does not reverse, just slow down on Flipsky 75100 by artsin » Sat, 2024-06-22 22:19 |
1 |
by artsin Tue, 2024-06-25 00:07 |
|
|
Need to integrate 4 motor controllers for sensored motors by charlesrwest » Sun, 2021-09-26 20:19 |
1 |
by skyline1970 Fri, 2021-10-29 12:01 |
|
|
using hall effect sensor for rpm detection by meisterpro » Wed, 2021-03-03 01:26 |
1 |
by vadicus Thu, 2021-03-04 18:12 |
|
|
Flipsky Mini FSESC4.2 Questions by Laurie Forbes » Sat, 2021-10-02 18:54 |
1 |
by skyline1970 Fri, 2021-10-29 12:09 |
|
|
Maytech SUPERFOC6.8 50A sub zero cooling for fun and burst power. Mosfet power loss? by Gargazol » Tue, 2020-10-20 14:12 |
1 |
by TheFallen Tue, 2020-10-27 16:38 |
|
|
One remote, two FSESC4.20 (wirelessly)? by fogus » Mon, 2020-10-26 17:42 |
1 |
by Rashid1992 Wed, 2022-08-31 10:32 |
|
|
Duel FSESC 4.12 to Flipsky VX1 Connection issue by Yafman » Mon, 2021-05-31 13:30 |
1 |
by neo Tue, 2021-06-15 02:43 |
|
|
Esc does not reply by nemethLali » Sun, 2021-08-01 16:07 |
1 |
by nemethLali Fri, 2021-08-06 22:18 |
|
|
Use different FET driver by Avin Raikwar » Fri, 2021-01-29 16:35 |
1 |
by skyline1970 Fri, 2021-01-29 21:00 |
|
|
How to start a new VESC 6 hardware project by olek130 » Sun, 2021-08-15 18:10 |
1 |
by vadicus Sun, 2021-08-22 04:31 |
|
|
Which hall sensor should i buy? by qwerasdf » Sun, 2021-09-19 19:50 |
1 |
by skyline1970 Sat, 2021-10-30 16:00 |
|
|
VESC 6 with 3 phase shunts to ground instead by shaman » Wed, 2019-01-30 21:23 |
2 |
by shaman Thu, 2019-01-31 15:33 |
Log in to post new content in the forum.
