You are here

Third Party Hardware

Topic / Topic startersort descending Replies Last post
Normal topic IGBT Vesc FOC not working
by ziumus » Sat, 2019-09-28 15:48
9
by bgdwiepp
Sat, 2019-10-19 21:56
Normal topic Incorrect R and L detection?
by vadicus » Mon, 2019-11-04 20:49
11
by vadicus
Fri, 2020-02-28 00:21
Normal topic Inductance measurement ?
by ziumus » Sat, 2019-05-25 21:31
3
by a.dahhak
Wed, 2020-06-03 21:48
Normal topic Information about "Das RS" and "Das mini" hardware using DRV8313/DRV8320
by hexakopter » Thu, 2018-04-26 19:18
3
by hexakopter
Wed, 2018-06-13 00:39
Normal topic Is my custom motor inductance too low?
by perpetum » Wed, 2020-11-04 18:01
2
by perpetum
Sat, 2020-11-28 18:28
Normal topic Issues flashing VESC HW 4.12
by Nic_cfar » Wed, 2020-10-21 00:08
0
by Nic_cfar
Wed, 2020-10-21 00:08
Normal topic Lack of throttle control / too fast
by mgisch » Mon, 2019-04-01 05:57
6
by mgisch
Wed, 2019-04-03 09:53
Normal topic Look at my amazing BLDC, see something weird? (help plz)
by javivi » Thu, 2020-02-06 16:19
4
by roelth
Sun, 2020-02-23 20:01
Normal topic Low power VESC - any available
by wdaehn » Wed, 2018-02-28 18:02
9
by TechAUmNu
Mon, 2018-03-19 11:54
Normal topic low voltage/power VESC
by qdxiatao » Sun, 2019-12-29 09:27
2
by qdxiatao
Mon, 2020-01-06 02:04
Normal topic Maker X Mini VESC burned at 46V. My fault or shitty quality?
by smileandbeware » Mon, 2019-11-18 10:53
3
by frank
Thu, 2019-12-26 15:27
Normal topic Massive overshoot in BLDC current control
by chris1seto » Tue, 2019-04-09 20:10
2
by frank
Thu, 2019-04-11 11:40
Normal topic Maytech 200A does not work in FOC, will a A200S work better?
by doom » Wed, 2019-08-07 20:40
1
by TechAUmNu
Fri, 2019-08-09 21:01
Normal topic Maytech esc 5V rail reads 0.5v
by hhhhghg » Fri, 2018-09-14 13:23
0
by hhhhghg
Fri, 2018-09-14 13:23
Normal topic MAYTECH ESC6 200A runs fine on 6s, faults immediately on 12s
by mxpro32 » Sun, 2019-06-30 21:39
3
by TechAUmNu
Tue, 2019-08-13 10:21
Normal topic maytech mto91hbm-nh motors hal sensor
by nolander » Thu, 2019-01-10 00:01
1
by sunsam8
Thu, 2019-01-10 11:15
Normal topic Maytech SUPERFOC6.8 50A sub zero cooling for fun and burst power. Mosfet power loss?
by Gargazol » Tue, 2020-10-20 14:12
1
by TheFallen
Tue, 2020-10-27 16:38
Normal topic Maytech VESC 4.10 UART issues
by LogixCraft » Tue, 2018-09-25 03:13
0
by LogixCraft
Tue, 2018-09-25 03:13
Normal topic Maytech VESC 6 FOC turn off without fault at high erpm, blower
by gabrield » Fri, 2020-05-15 01:16
0
by gabrield
Fri, 2020-05-15 01:24
Normal topic Maytech VESC duty cycle & PID control problems
by subodh.malgonde » Mon, 2018-10-01 11:49
1
by subodh.malgonde
Tue, 2018-10-02 11:59
Normal topic Maytech VESC keeps startup spinning slowly
by Snorreman » Mon, 2018-09-24 09:57
0
by Snorreman
Mon, 2018-09-24 09:57
Normal topic MICRO Module
by F4metz » Sat, 2019-03-02 15:10
3
by chuttney1
Sun, 2019-03-03 18:54
Normal topic MINI FOC from MakerX
by YUTW » Thu, 2019-08-08 11:17
1
by speed3r
Tue, 2019-08-13 10:17
Normal topic Mini/micro/nano VESC solutions?
by Cham » Mon, 2020-09-21 17:34
3
by Cham
Thu, 2020-09-24 12:15
Hot topic MINI4 (Page: 1, 2)
by antonchromjak » Sun, 2017-11-26 16:08
57
by jskeels.5843
Tue, 2020-05-19 02:16
New posts
No new posts
Hot topic with new posts
Hot topic without new posts
Sticky topic
Locked topic
Subscribe to RSS - Third Party Hardware