You are here

Third Party Hardware

Topic / Topic startersort descending Replies Last post
Normal topic low voltage/power VESC
by qdxiatao » Sun, 2019-12-29 09:27
2
by qdxiatao
Mon, 2020-01-06 02:04
Normal topic Lowest power/smallest available 3rd party board?
by doctarr » Sun, 2021-03-07 15:28
4
by doctarr
Mon, 2021-03-08 12:38
Normal topic make and make upload okay, but no connection
by martin2day » Tue, 2021-02-16 19:19
3
by CTSchorsch
Wed, 2021-02-17 14:02
Normal topic Maker X Mini VESC burned at 46V. My fault or shitty quality?
by smileandbeware » Mon, 2019-11-18 10:53
3
by frank
Thu, 2019-12-26 15:27
Normal topic Makerbase (new) 84200hp 'quirky' on/off 'bug'?
by flez1966 » Wed, 2024-03-20 17:06
3
by Huang_jh
Thu, 2024-10-17 13:24
Normal topic Makerbase VESC 84200HP It won't turn on.
by Deejii23 » Sun, 2024-11-24 16:31
1
by Deejii23
Thu, 2024-11-28 18:58
Normal topic MakerX 75/200 - destroyed USB-Port
by jangrik » Wed, 2022-02-23 22:01
1
by jangrik
Thu, 2022-02-24 09:49
Normal topic Massive overshoot in BLDC current control
by chris1seto » Tue, 2019-04-09 20:10
2
by frank
Thu, 2019-04-11 11:40
Normal topic Maytech 100a ESC
by NOldfield » Sat, 2023-04-22 08:51
0
by NOldfield
Mon, 2023-04-24 15:32
Normal topic Maytech 200A does not work in FOC, will a A200S work better?
by doom » Wed, 2019-08-07 20:40
1
by TechAUmNu
Fri, 2019-08-09 21:01
Normal topic Maytech esc 5V rail reads 0.5v
by hhhhghg » Fri, 2018-09-14 13:23
0
by hhhhghg
Fri, 2018-09-14 13:23
Normal topic MAYTECH ESC6 200A runs fine on 6s, faults immediately on 12s
by mxpro32 » Sun, 2019-06-30 21:39
3
by TechAUmNu
Tue, 2019-08-13 10:21
Normal topic maytech mto91hbm-nh motors hal sensor
by nolander » Thu, 2019-01-10 00:01
1
by sunsam8
Thu, 2019-01-10 11:15
Normal topic Maytech SUPERFOC6.8 50A sub zero cooling for fun and burst power. Mosfet power loss?
by Gargazol » Tue, 2020-10-20 14:12
1
by TheFallen
Tue, 2020-10-27 16:38
Normal topic Maytech VESC 4.10 UART issues
by LogixCraft » Tue, 2018-09-25 03:13
0
by LogixCraft
Tue, 2018-09-25 03:13
Normal topic Maytech VESC 6 FOC turn off without fault at high erpm, blower
by gabrield » Fri, 2020-05-15 01:16
2
by ImperialSB
Thu, 2021-04-22 17:54
Normal topic Maytech VESC duty cycle & PID control problems
by subodh.malgonde » Mon, 2018-10-01 11:49
1
by subodh.malgonde
Tue, 2018-10-02 11:59
Normal topic Maytech VESC keeps startup spinning slowly
by Snorreman » Mon, 2018-09-24 09:57
0
by Snorreman
Mon, 2018-09-24 09:57
Normal topic MICRO Module
by F4metz » Sat, 2019-03-02 15:10
3
by chuttney1
Sun, 2019-03-03 18:54
Normal topic MINI 4 having DRV8301 in mini4.h !
by snakeplissken » Fri, 2023-11-24 20:58
1
by justlovescience
Tue, 2024-02-06 16:36
Normal topic MINI FOC from MakerX
by YUTW » Thu, 2019-08-08 11:17
1
by speed3r
Tue, 2019-08-13 10:17
Normal topic Mini/micro/nano VESC solutions?
by Cham » Mon, 2020-09-21 17:34
3
by Cham
Thu, 2020-09-24 12:15
Hot topic MINI4 (Page: 1, 2)
by antonchromjak » Sun, 2017-11-26 16:08
61
by roque.canales
Fri, 2023-09-29 13:54
Normal topic mksvesc 84200
by Nubi » Sat, 2024-08-10 00:48
2
by Huang_jh
Thu, 2024-10-17 12:55
Normal topic Modified version of mini4,during motor detection,fault_code_drv-11 was reported
by qdxiatao » Mon, 2022-10-31 07:42
0
by qdxiatao
Mon, 2022-10-31 07:42
New posts
No new posts
Hot topic with new posts
Hot topic without new posts
Sticky topic
Locked topic
Subscribe to RSS - Third Party Hardware