You are here
Third Party Hardware
Log in to post new content in the forum.
Topic / Topic starter | Replies | Last post | |
---|---|---|---|
Information about "Das RS" and "Das mini" hardware using DRV8313/DRV8320 by hexakopter » Thu, 2018-04-26 19:18 |
3 |
by hexakopter Wed, 2018-06-13 00:39 |
|
Is it possible to run VESC software on a STM32G431? by WackoKacko » Mon, 2023-02-06 11:52 |
2 |
by Svein Utne Tue, 2023-03-07 13:58 |
|
Is my custom motor inductance too low? by perpetum » Wed, 2020-11-04 18:01 |
2 |
by perpetum Sat, 2020-11-28 18:28 |
|
Is there a way to deactivate roll to start function FW 5.02 by Philo » Sun, 2021-04-11 13:55 |
0 |
by Philo Sun, 2021-04-11 13:58 |
|
Issues flashing VESC HW 4.12 by Nic_cfar » Wed, 2020-10-21 00:08 |
1 |
by xeniter Mon, 2021-09-13 22:33 |
|
Lack of throttle control / too fast by mgisch » Mon, 2019-04-01 05:57 |
6 |
by mgisch Wed, 2019-04-03 09:53 |
|
Look at my amazing BLDC, see something weird? (help plz) by javivi » Thu, 2020-02-06 16:19 |
4 |
by roelth Sun, 2020-02-23 20:01 |
|
Looking for paid help to customize VESC board by jwardellMLA » Thu, 2022-06-09 20:34 |
0 |
by jwardellMLA Thu, 2022-06-09 20:34 |
|
LoRa Support by CTSchorsch » Fri, 2021-12-17 13:59 |
0 |
by CTSchorsch Fri, 2021-12-17 13:59 |
|
Losing configuration and imu drift by AngelKillR » Sat, 2022-07-09 05:48 |
2 |
by Lennart Duijn Thu, 2023-06-01 18:24 |
|
Low power VESC - any available by wdaehn » Wed, 2018-02-28 18:02 |
9 |
by TechAUmNu Mon, 2018-03-19 11:54 |
|
low voltage/power VESC by qdxiatao » Sun, 2019-12-29 09:27 |
2 |
by qdxiatao Mon, 2020-01-06 02:04 |
|
Lowest power/smallest available 3rd party board? by doctarr » Sun, 2021-03-07 15:28 |
4 |
by doctarr Mon, 2021-03-08 12:38 |
|
make and make upload okay, but no connection by martin2day » Tue, 2021-02-16 19:19 |
3 |
by CTSchorsch Wed, 2021-02-17 14:02 |
|
Maker X Mini VESC burned at 46V. My fault or shitty quality? by smileandbeware » Mon, 2019-11-18 10:53 |
3 |
by frank Thu, 2019-12-26 15:27 |
|
MakerX 75/200 - destroyed USB-Port by jangrik » Wed, 2022-02-23 22:01 |
1 |
by jangrik Thu, 2022-02-24 09:49 |
|
Massive overshoot in BLDC current control by chris1seto » Tue, 2019-04-09 20:10 |
2 |
by frank Thu, 2019-04-11 11:40 |
|
Maytech 100a ESC by NOldfield » Sat, 2023-04-22 08:51 |
0 |
by NOldfield Mon, 2023-04-24 15:32 |
|
Maytech 200A does not work in FOC, will a A200S work better? by doom » Wed, 2019-08-07 20:40 |
1 |
by TechAUmNu Fri, 2019-08-09 21:01 |
|
Maytech esc 5V rail reads 0.5v by hhhhghg » Fri, 2018-09-14 13:23 |
0 |
by hhhhghg Fri, 2018-09-14 13:23 |
|
MAYTECH ESC6 200A runs fine on 6s, faults immediately on 12s by mxpro32 » Sun, 2019-06-30 21:39 |
3 |
by TechAUmNu Tue, 2019-08-13 10:21 |
|
maytech mto91hbm-nh motors hal sensor by nolander » Thu, 2019-01-10 00:01 |
1 |
by sunsam8 Thu, 2019-01-10 11:15 |
|
Maytech SUPERFOC6.8 50A sub zero cooling for fun and burst power. Mosfet power loss? by Gargazol » Tue, 2020-10-20 14:12 |
1 |
by TheFallen Tue, 2020-10-27 16:38 |
|
Maytech VESC 4.10 UART issues by LogixCraft » Tue, 2018-09-25 03:13 |
0 |
by LogixCraft Tue, 2018-09-25 03:13 |
|
Maytech VESC 6 FOC turn off without fault at high erpm, blower by gabrield » Fri, 2020-05-15 01:16 |
2 |
by ImperialSB Thu, 2021-04-22 17:54 |
Log in to post new content in the forum.