You are here

Third Party Hardware

Topic / Topic startersort descending Replies Last post
Normal topic Have i bricked my flipsky FSESC 4.20?
by olletj » Sat, 2022-01-22 18:03
2
by olletj
Mon, 2022-01-31 21:18
Normal topic HELP set current settings for inverter
by ka_ru » Wed, 2020-11-18 20:51
2
by ka_ru
Mon, 2020-11-23 11:41
Normal topic Help with noise in rpm and ppm
by martin2day » Wed, 2021-02-24 14:22
2
by martin2day
Wed, 2021-02-24 20:19
Normal topic Here lies the thread for hardware powered by stm32
by neo » Tue, 2021-06-15 00:47
7
by neo
Tue, 2021-06-15 01:43
Normal topic HIGH Voltage (350v-450v) VESC
by athlon » Sun, 2018-11-25 18:34
7
by thewho
Tue, 2019-02-26 12:38
Hot topic High Voltage ESC (HiVEsc) 150V 500A
by e-biker » Thu, 2019-08-15 14:45
19
by jarrancho
Fri, 2020-12-04 11:35
Normal topic Hooking up two or more motor drivers to the same MCU
by darkclaude » Thu, 2019-06-20 10:02
4
by skyline1970
Wed, 2019-07-31 13:53
Normal topic How to change the Phase PWM polarity
by Boben » Fri, 2021-04-02 20:51
0
by Boben
Fri, 2021-04-02 20:51
Normal topic How to fix VESC killed by over current in serial comm?
by 8bit » Sun, 2021-05-16 04:02
4
by neo
Sat, 2021-06-12 02:00
Normal topic How to start a new VESC 6 hardware project
by olek130 » Sun, 2021-08-15 18:10
1
by vadicus
Sun, 2021-08-22 04:31
Normal topic How to upload firmware on MINI4 ?
by john » Mon, 2018-11-12 10:55
1
by john
Mon, 2018-11-12 11:59
Normal topic HW advice : repair , vesc 4.12, vesc 6.4 or better wait ?
by frameto » Sun, 2017-11-19 21:36
1
by josh
Thu, 2018-07-26 18:47
Normal topic HW4.12 Firmware trouble
by CTSchorsch » Wed, 2018-12-05 21:09
4
by sam.vanratt
Fri, 2018-12-28 17:55
Normal topic Hyper-V No "New" button in the action pane
by Gheer » Tue, 2020-11-17 13:02
0
by Gheer
Tue, 2020-11-17 13:02
Normal topic I can't communicate with the VESC-Clone
by Savavit » Sun, 2019-10-27 17:42
1
by vadicus
Thu, 2019-11-07 06:48
Normal topic I can't get my fresc to work I think all the leds are lighting up but when I pull the trigger on the remote nothing happens
by pdxcjc » Fri, 2022-03-11 17:46
5
by Gatze
Mon, 2022-05-09 17:03
Normal topic I need help designing 200v 80a vesc
by qwerasdf » Mon, 2021-05-03 17:08
8
by dylanu
Thu, 2022-04-14 06:29
Normal topic I Need Some Guidance With My Schematic 16s 50a
by qwerasdf » Sat, 2022-01-01 15:04
6
by mckenzie.keith
Fri, 2022-01-14 04:39
Normal topic IGBT Vesc FOC not working
by ziumus » Sat, 2019-09-28 15:48
9
by bgdwiepp
Sat, 2019-10-19 21:56
Normal topic INA240A1 replacement
by CTSchorsch » Thu, 2021-11-11 15:50
3
by skyline1970
Sat, 2021-11-13 11:37
Normal topic Incorrect R and L detection?
by vadicus » Mon, 2019-11-04 20:49
11
by vadicus
Fri, 2020-02-28 00:21
Normal topic Inductance measurement ?
by ziumus » Sat, 2019-05-25 21:31
3
by a.dahhak
Wed, 2020-06-03 21:48
Normal topic Information about "Das RS" and "Das mini" hardware using DRV8313/DRV8320
by hexakopter » Thu, 2018-04-26 19:18
3
by hexakopter
Wed, 2018-06-13 00:39
Normal topic Is my custom motor inductance too low?
by perpetum » Wed, 2020-11-04 18:01
2
by perpetum
Sat, 2020-11-28 18:28
Normal topic Is there a way to deactivate roll to start function FW 5.02
by Philo » Sun, 2021-04-11 13:55
0
by Philo
Sun, 2021-04-11 13:58
New posts
No new posts
Hot topic with new posts
Hot topic without new posts
Sticky topic
Locked topic
Subscribe to RSS - Third Party Hardware