You are here
Third Party Hardware
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Gate driver by RSR » Sat, 2019-01-26 21:46 |
1 |
by bgdwiepp Fri, 2019-03-01 15:21 |
|
|
3 shunt low side resistor configuration based on VESC 6 by jordanlow » Thu, 2019-02-14 16:42 |
1 |
by TechAUmNu Thu, 2019-02-14 18:31 |
|
|
84v VESC?? by larsrocket » Sun, 2018-04-01 22:41 |
1 |
by larsrocket Mon, 2018-04-30 19:59 |
|
|
Flipsky 75200 struggle/cogging on higher voltage >>> Solution by Strippenstrolch321 » Sun, 2022-06-26 16:25 |
1 |
by Strippenstrolch321 Wed, 2022-06-29 19:57 |
|
|
Comms plug an leads by craig w » Thu, 2021-12-23 23:33 |
1 |
by skyline1970 Fri, 2021-12-24 09:31 |
|
|
FSESC75100 Doesn't Work When Unplugged by zapshe » Fri, 2022-07-29 12:06 |
1 |
by zapshe Wed, 2022-08-17 22:34 |
|
|
Flipsky FSESC v4.20 suddenly flashing error code by JustWantRun » Thu, 2020-08-06 18:44 |
1 |
by JustWantRun Thu, 2020-08-06 19:22 |
|
|
Can't update firmware FSESC 4.12 by TimBilliet » Tue, 2019-11-26 21:52 |
1 |
by TechAUmNu Wed, 2019-11-27 14:47 |
|
|
What about using the Votol em150 3kw 48-72v? by Arpanx » Sat, 2020-03-21 11:23 |
1 |
by vadicus Mon, 2020-03-23 20:15 |
|
|
Maytech 200A does not work in FOC, will a A200S work better? by doom » Wed, 2019-08-07 20:40 |
1 |
by TechAUmNu Fri, 2019-08-09 21:01 |
|
|
config wanted, for 75100 with ebike geared hub motor by tom355 » Mon, 2023-02-20 09:51 |
1 |
by Oded Mazor Fri, 2023-02-24 15:08 |
|
|
Cheap Focer Troubleshoot DRV by Niklas Probst » Mon, 2023-03-13 08:22 |
1 |
by Niklas Probst Mon, 2023-03-13 12:54 |
|
|
VESC 75/300 half bridge burns out when I switch to FOC mode by vajasgeri » Thu, 2023-05-04 14:02 |
1 |
by vadicus Fri, 2023-05-05 19:40 |
|
|
VESC Design - Review and Bringup - 150V - 20A by ripperpc » Sat, 2019-09-21 17:30 |
1 |
by TechAUmNu Mon, 2019-09-30 14:34 |
|
|
I can't communicate with the VESC-Clone by Savavit » Sun, 2019-10-27 17:42 |
1 |
by vadicus Thu, 2019-11-07 06:48 |
|
|
Esc does not reply by nemethLali » Sun, 2021-08-01 16:07 |
1 |
by nemethLali Fri, 2021-08-06 22:18 |
|
|
Use different FET driver by Avin Raikwar » Fri, 2021-01-29 16:35 |
1 |
by skyline1970 Fri, 2021-01-29 21:00 |
|
|
How to start a new VESC 6 hardware project by olek130 » Sun, 2021-08-15 18:10 |
1 |
by vadicus Sun, 2021-08-22 04:31 |
|
|
Which hall sensor should i buy? by qwerasdf » Sun, 2021-09-19 19:50 |
1 |
by skyline1970 Sat, 2021-10-30 16:00 |
|
|
Need to integrate 4 motor controllers for sensored motors by charlesrwest » Sun, 2021-09-26 20:19 |
1 |
by skyline1970 Fri, 2021-10-29 12:01 |
|
|
using hall effect sensor for rpm detection by meisterpro » Wed, 2021-03-03 01:26 |
1 |
by vadicus Thu, 2021-03-04 18:12 |
|
|
Flipsky Mini FSESC4.2 Questions by Laurie Forbes » Sat, 2021-10-02 18:54 |
1 |
by skyline1970 Fri, 2021-10-29 12:09 |
|
|
Maytech SUPERFOC6.8 50A sub zero cooling for fun and burst power. Mosfet power loss? by Gargazol » Tue, 2020-10-20 14:12 |
1 |
by TheFallen Tue, 2020-10-27 16:38 |
|
|
One remote, two FSESC4.20 (wirelessly)? by fogus » Mon, 2020-10-26 17:42 |
1 |
by Rashid1992 Wed, 2022-08-31 10:32 |
|
|
Duel FSESC 4.12 to Flipsky VX1 Connection issue by Yafman » Mon, 2021-05-31 13:30 |
1 |
by neo Tue, 2021-06-15 02:43 |
Log in to post new content in the forum.
