You are here
Third Party Hardware
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Porting VESC firmware to ODrive hardware by Remind » Wed, 2021-06-30 01:39 |
3 |
by vadicus Thu, 2021-07-08 07:34 |
|
|
Inductance measurement ? by ziumus » Sat, 2019-05-25 21:31 |
3 |
by a.dahhak Wed, 2020-06-03 21:48 |
|
|
commercially available +120V +25kW controller by grasshoppersystem » Fri, 2022-05-27 20:23 |
3 |
by vadicus Mon, 2022-07-11 18:13 |
|
|
INA240A1 replacement by CTSchorsch » Thu, 2021-11-11 15:50 |
3 |
by skyline1970 Sat, 2021-11-13 11:37 |
|
|
Change maximum allowed input voltage by CTSchorsch » Mon, 2021-12-13 21:37 |
3 |
by Er-Chispa Mon, 2025-10-06 18:05 |
|
|
PWM timer issues on high voltage by pegasus-aero » Tue, 2022-01-04 01:39 |
3 |
by pegasus-aero Thu, 2022-01-13 00:37 |
|
|
BitWizard ESC thermal Mod 100A cont. by Philipp Spindler » Thu, 2018-05-24 16:01 |
3 |
by Roger Wolff Thu, 2018-05-24 18:10 |
|
|
SAFETY ADVICE third party controllers with separate power and logic board by JakeTheSnake » Wed, 2022-10-12 11:50 |
3 |
by TechAUmNu Thu, 2022-12-29 14:16 |
|
|
Motor Setup issues e-Snowboard by arosenthal » Fri, 2020-09-18 21:10 |
3 |
by etadada12 Sun, 2020-11-29 02:17 |
|
|
Vesc Tool with Tenka, firmware error by DankPoppin » Sun, 2023-05-28 20:39 |
3 |
by jaymacnulty Fri, 2023-07-14 07:30 |
|
|
Makerbase (new) 84200hp 'quirky' on/off 'bug'? by flez1966 » Wed, 2024-03-20 17:06 |
3 |
by Huang_jh Thu, 2024-10-17 13:24 |
|
|
Flipsky BLDC motor reporting wrong rpm and cant use hall effects by TonyD » Fri, 2024-03-29 18:44 |
3 |
by TonyD Wed, 2024-04-03 16:06 |
|
|
DIY vesc 75/300 variant power stage problem by motordriver111 » Sat, 2021-03-27 21:44 |
2 |
by vadicus Tue, 2021-04-06 18:50 |
|
|
Problems with Maytech MTVESC6.12 by TheJohnson » Mon, 2020-10-19 04:50 |
2 |
by TheJohnson Wed, 2020-10-21 09:39 |
|
|
Is my custom motor inductance too low? by perpetum » Wed, 2020-11-04 18:01 |
2 |
by perpetum Sat, 2020-11-28 18:28 |
|
|
HELP set current settings for inverter by ka_ru » Wed, 2020-11-18 20:51 |
2 |
by ka_ru Mon, 2020-11-23 11:41 |
|
|
Regenerative Braking with Lead Acid Batteries by daniel.cox@cant... » Sat, 2021-06-12 00:47 |
2 |
by neo Tue, 2021-06-15 01:09 |
|
|
Motor is too loud, are there settings to quiet it? by Jason Toews » Thu, 2021-09-23 20:49 |
2 |
by Laurie Forbes Thu, 2021-09-30 18:57 |
|
|
Help with noise in rpm and ppm by martin2day » Wed, 2021-02-24 14:22 |
2 |
by martin2day Wed, 2021-02-24 20:19 |
|
|
VX2 wont connect to to stormcore 60d by KratomChris » Sun, 2022-04-03 13:45 |
2 |
by Madrid Yeti Sat, 2022-06-25 19:46 |
|
|
Is it possible to run VESC software on a STM32G431? by WackoKacko » Mon, 2023-02-06 11:52 |
2 |
by Svein Utne Tue, 2023-03-07 13:58 |
|
|
VESC 6 with 3 phase shunts to ground instead by shaman » Wed, 2019-01-30 21:23 |
2 |
by shaman Thu, 2019-01-31 15:33 |
|
|
(Open source) BMS by soltesz » Mon, 2017-12-18 00:26 |
2 |
by Pimousse Mon, 2018-01-08 16:26 |
|
|
Losing configuration and imu drift by AngelKillR » Sat, 2022-07-09 05:48 |
2 |
by Lennart Duijn Thu, 2023-06-01 18:24 |
|
|
Fault finding on failed VESC by dmcke5 » Sun, 2019-02-17 01:57 |
2 |
by benjamin Wed, 2019-03-13 10:00 |
Log in to post new content in the forum.
