You are here
Third Party Hardware
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Help with noise in rpm and ppm by martin2day » Wed, 2021-02-24 14:22 |
2 |
by martin2day Wed, 2021-02-24 20:19 |
|
|
DIY vesc 75/300 variant power stage problem by motordriver111 » Sat, 2021-03-27 21:44 |
2 |
by vadicus Tue, 2021-04-06 18:50 |
|
|
Problems with Maytech MTVESC6.12 by TheJohnson » Mon, 2020-10-19 04:50 |
2 |
by TheJohnson Wed, 2020-10-21 09:39 |
|
|
Is my custom motor inductance too low? by perpetum » Wed, 2020-11-04 18:01 |
2 |
by perpetum Sat, 2020-11-28 18:28 |
|
|
HELP set current settings for inverter by ka_ru » Wed, 2020-11-18 20:51 |
2 |
by ka_ru Mon, 2020-11-23 11:41 |
|
|
VESC 6 With AS5047 encoder by Geir Henriksen » Tue, 2018-07-31 00:09 |
2 |
by frank Mon, 2018-08-20 09:32 |
|
|
Massive overshoot in BLDC current control by chris1seto » Tue, 2019-04-09 20:10 |
2 |
by frank Thu, 2019-04-11 11:40 |
|
|
4.12 Phase current/voltage sense mix up. Need assistance please. by shaman » Tue, 2019-01-29 14:58 |
2 |
by shaman Tue, 2019-01-29 16:24 |
|
|
Custom Hardware - FET shoot-through problem - oscilloscope captures by ben5243 » Tue, 2019-02-19 03:58 |
2 |
by TechAUmNu Sat, 2019-03-16 00:27 |
|
|
FS75100 by Filip Kinl » Sun, 2022-02-27 16:42 |
2 |
by Oded Mazor Thu, 2022-03-24 12:02 |
|
|
VX2 wont connect to to stormcore 60d by KratomChris » Sun, 2022-04-03 13:45 |
2 |
by Madrid Yeti Sat, 2022-06-25 19:46 |
|
|
Is it possible to run VESC software on a STM32G431? by WackoKacko » Mon, 2023-02-06 11:52 |
2 |
by Svein Utne Tue, 2023-03-07 13:58 |
|
|
Losing configuration and imu drift by AngelKillR » Sat, 2022-07-09 05:48 |
2 |
by Lennart Duijn Thu, 2023-06-01 18:24 |
|
|
Have i bricked my flipsky FSESC 4.20? by olletj » Sat, 2022-01-22 18:03 |
2 |
by olletj Mon, 2022-01-31 21:18 |
|
|
SpaceVESC, a modular small VESC by SpaceVESCproject » Wed, 2019-10-02 21:35 |
2 |
by frank Thu, 2019-10-17 11:47 |
|
|
New need help by VinnyF » Tue, 2019-12-10 13:16 |
2 |
by tex Wed, 2019-12-11 17:19 |
|
|
Vx1 controller help by stefann » Wed, 2020-03-11 12:42 |
2 |
by stefann Sun, 2020-03-15 00:36 |
|
|
Maytech VESC 6 FOC turn off without fault at high erpm, blower by gabrield » Fri, 2020-05-15 01:16 |
2 |
by ImperialSB Thu, 2021-04-22 17:54 |
|
|
Sailboat Controller/Motor/Generator by Joe Lorkovic » Thu, 2020-05-28 21:55 |
2 |
by Eric Crouch Sat, 2020-06-06 19:11 |
|
|
Flipsky 75100 Pro V2.0 + Ninebot Max G2 motor: FOC auto-detection failure by Killbot283 » Fri, 2026-06-26 14:49 |
2 |
by nikolaygenov79 Fri, 2026-07-03 13:34 |
|
|
Shunt resistor replacement and too high motor current by lacondro » Mon, 2024-03-25 05:56 |
2 |
by lacondro Wed, 2024-03-27 09:55 |
|
|
wrong amps reading (realtime data) by flez1966 » Wed, 2024-03-27 13:55 |
2 |
by B1996 Tue, 2024-12-03 07:26 |
|
|
compatability assistance by NRGFPV » Mon, 2020-12-28 04:58 |
2 |
by NRGFPV Wed, 2020-12-30 08:46 |
|
|
Connect PixHawk 4 to FSESC 4.12 by iwdok » Tue, 2021-10-19 11:18 |
2 |
by frank Wed, 2021-12-01 13:38 |
|
|
Firmware flash on new born board by matrixgti » Thu, 2020-10-08 20:39 |
2 |
by TechAUmNu Tue, 2020-10-13 10:18 |
Log in to post new content in the forum.
