You are here
Third Party Hardware
Log in to post new content in the forum.
Topic / Topic starter | Replies | Last post | |
---|---|---|---|
Maytech VESC 6 FOC turn off without fault at high erpm, blower by gabrield » Fri, 2020-05-15 01:16 |
2 |
by ImperialSB Thu, 2021-04-22 17:54 |
|
Sailboat Controller/Motor/Generator by Joe Lorkovic » Thu, 2020-05-28 21:55 |
2 |
by Eric Crouch Sat, 2020-06-06 19:11 |
|
SpaceVESC, a modular small VESC by SpaceVESCproject » Wed, 2019-10-02 21:35 |
2 |
by frank Thu, 2019-10-17 11:47 |
|
New need help by VinnyF » Tue, 2019-12-10 13:16 |
2 |
by tex Wed, 2019-12-11 17:19 |
|
Vx1 controller help by stefann » Wed, 2020-03-11 12:42 |
2 |
by stefann Sun, 2020-03-15 00:36 |
|
VESC 6 with 3 phase shunts to ground instead by shaman » Wed, 2019-01-30 21:23 |
2 |
by shaman Thu, 2019-01-31 15:33 |
|
(Open source) BMS by soltesz » Mon, 2017-12-18 00:26 |
2 |
by Pimousse Mon, 2018-01-08 16:26 |
|
Fault finding on failed VESC by dmcke5 » Sun, 2019-02-17 01:57 |
2 |
by benjamin Wed, 2019-03-13 10:00 |
|
Custom PCB based on 6.4 by CTSchorsch » Wed, 2019-02-20 11:49 |
2 |
by CTSchorsch Mon, 2020-01-20 07:30 |
|
Motor is too loud, are there settings to quiet it? by Jason Toews » Thu, 2021-09-23 20:49 |
2 |
by Laurie Forbes Thu, 2021-09-30 18:57 |
|
Help with noise in rpm and ppm by martin2day » Wed, 2021-02-24 14:22 |
2 |
by martin2day Wed, 2021-02-24 20:19 |
|
DIY vesc 75/300 variant power stage problem by motordriver111 » Sat, 2021-03-27 21:44 |
2 |
by vadicus Tue, 2021-04-06 18:50 |
|
Problems with Maytech MTVESC6.12 by TheJohnson » Mon, 2020-10-19 04:50 |
2 |
by TheJohnson Wed, 2020-10-21 09:39 |
|
Is my custom motor inductance too low? by perpetum » Wed, 2020-11-04 18:01 |
2 |
by perpetum Sat, 2020-11-28 18:28 |
|
HELP set current settings for inverter by ka_ru » Wed, 2020-11-18 20:51 |
2 |
by ka_ru Mon, 2020-11-23 11:41 |
|
Regenerative Braking with Lead Acid Batteries by daniel.cox@cant... » Sat, 2021-06-12 00:47 |
2 |
by neo Tue, 2021-06-15 01:09 |
|
VX2 wont connect to to stormcore 60d by KratomChris » Sun, 2022-04-03 13:45 |
2 |
by Madrid Yeti Sat, 2022-06-25 19:46 |
|
Is it possible to run VESC software on a STM32G431? by WackoKacko » Mon, 2023-02-06 11:52 |
2 |
by Svein Utne Tue, 2023-03-07 13:58 |
|
Losing configuration and imu drift by AngelKillR » Sat, 2022-07-09 05:48 |
2 |
by Lennart Duijn Thu, 2023-06-01 18:24 |
|
Have i bricked my flipsky FSESC 4.20? by olletj » Sat, 2022-01-22 18:03 |
2 |
by olletj Mon, 2022-01-31 21:18 |
|
FS75100 by Filip Kinl » Sun, 2022-02-27 16:42 |
2 |
by Oded Mazor Thu, 2022-03-24 12:02 |
|
Motor Setup issues e-Snowboard by arosenthal » Fri, 2020-09-18 21:10 |
3 |
by etadada12 Sun, 2020-11-29 02:17 |
|
BitWizard ESC thermal Mod 100A cont. by Philipp Spindler » Thu, 2018-05-24 16:01 |
3 |
by Roger Wolff Thu, 2018-05-24 18:10 |
|
Inductance measurement ? by ziumus » Sat, 2019-05-25 21:31 |
3 |
by a.dahhak Wed, 2020-06-03 21:48 |
|
Porting VESC firmware to ODrive hardware by Remind » Wed, 2021-06-30 01:39 |
3 |
by vadicus Thu, 2021-07-08 07:34 |
Log in to post new content in the forum.