You are here
VESC Original Hardware
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
VESC 75/300 current noise / losing sync? by ezonca » Thu, 2019-10-03 23:06 |
2 |
by benjamin Thu, 2019-10-10 07:56 |
|
|
VESC 4.12 - Data loss on power off by da_rul0r » Wed, 2019-08-14 16:43 |
2 |
by da_rul0r Thu, 2019-08-15 08:33 |
|
|
Hooking up two or more motor drivers to the same MCU by darkclaude » Thu, 2019-06-20 10:02 |
2 |
by skyline1970 Wed, 2019-07-31 13:53 |
|
|
VESC Hardware by eschroff » Thu, 2019-07-25 02:38 |
1 |
by skyline1970 Wed, 2019-07-31 13:35 |
|
|
Programming Vesc 4.12 motor spin only in detection mode by DanieleRA » Sun, 2019-07-28 16:29 |
0 |
by DanieleRA Sun, 2019-07-28 16:29 |
|
|
dual VESC battery current by chris_winkel » Tue, 2019-06-18 15:26 |
0 |
by chris_winkel Tue, 2019-06-18 15:26 |
|
|
How exactly do I connect a VESC 6.4 to an Arduino Nano? by MaxMaker1 » Tue, 2018-07-03 23:18 |
5 |
by molak Tue, 2019-06-04 19:39 |
|
|
Fault: FAULT_CODE_HIGH_OFFSET_CURRENT_SENSOR_3 on VESC 6 by Jackl » Tue, 2019-05-28 14:48 |
0 |
by Jackl Tue, 2019-05-28 14:48 |
|
|
Servomotor control with VESC6 by Humberto Estrada » Wed, 2019-05-22 16:15 |
0 |
by Humberto Estrada Wed, 2019-05-22 16:15 |
|
|
Trampa boards online store by jrowe » Tue, 2019-04-16 06:28 |
0 |
by jrowe Tue, 2019-04-16 06:28 |
|
|
Inductance (L) measurement by rahmaev_a_o » Tue, 2018-08-07 10:10 |
4 |
by benjamin Sat, 2019-02-23 10:11 |
|
|
VESC on 48V 1500W HUB motor by jordanlow » Sat, 2019-01-12 14:52 |
4 |
by jordanlow Thu, 2019-01-24 04:14 |
|
|
Flashing via SWD works, but no green LED or USB enumeration by vpl » Fri, 2018-11-16 17:48 |
1 |
by vpl Wed, 2018-11-21 17:27 |
|
|
Using ABI Encoders by danielw » Tue, 2018-10-30 14:33 |
1 |
by danielw Wed, 2018-11-07 15:38 |
|
|
HW 4.12 Change low voltage cutoff by subodh.malgonde » Tue, 2018-09-18 07:31 |
7 |
by TheFallen Thu, 2018-09-20 09:51 |
|
|
Adding capacitors with long power cables? by rich » Thu, 2017-09-07 20:40 |
6 |
by frank Mon, 2018-08-20 09:12 |
|
|
Different HW versions for V6?! by Marc Pflugmann » Sun, 2018-06-24 13:43 |
1 |
by frank Mon, 2018-06-25 13:01 |
|
|
VESC 6.4 supplys Arduino over SIGNAL!! by MaxMaker1 » Thu, 2018-05-24 15:02 |
4 |
by frank Mon, 2018-06-04 23:24 |
|
|
Input Voltage on PPM (Servo) VESC6? by Marc Pflugmann » Fri, 2018-05-25 21:02 |
3 |
by Roger Wolff Thu, 2018-05-31 08:05 |
|
|
Vesc4 have 2 Analog output pins? by greensightag.com » Sat, 2018-05-12 00:42 |
1 |
by Roger Wolff Tue, 2018-05-15 10:51 |
|
|
HARDWARE QUESTION: Maximum AC voltage VESC can tolerate? by danvel » Fri, 2018-04-27 15:31 |
4 |
by Roger Wolff Mon, 2018-05-14 22:13 |
|
|
Mechanical dimensions of VESC 6 by ufechner » Sat, 2018-04-28 19:01 |
2 |
by TechAUmNu Mon, 2018-04-30 22:28 |
|
|
DRV8302 Gate drive limitations by nickw1881 » Sun, 2018-04-29 09:56 |
0 |
by nickw1881 Sun, 2018-04-29 09:56 |
|
|
How to wire Cruise Control with VESC6 ADC by Tilman Baumann » Tue, 2018-04-10 11:11 |
0 |
by Tilman Baumann Tue, 2018-04-10 11:11 |
|
|
HW 4.12 USB Device Descriptor Failed-> Red light flashed on start by MTBVASEY » Wed, 2018-04-04 11:06 |
2 |
by MTBVASEY Wed, 2018-04-04 22:24 |
Log in to post new content in the forum.
