You are here
VESC Original Hardware
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
2xVESC6.0 with identical T-Motor different start up result by tobiokanobi » Fri, 2024-10-04 15:26 |
3 |
by tobiokanobi Fri, 2024-10-04 23:07 |
|
|
75/300 Layout or gerbers by Chapel81 » Fri, 2020-08-28 21:27 |
3 |
by Chapel81 Wed, 2020-09-09 16:24 |
|
|
VESC 75/300 Frying in BLDC Regen by ezonca » Fri, 2020-10-23 21:53 |
3 |
by TechAUmNu Thu, 2020-10-29 13:43 |
|
|
Input Voltage on PPM (Servo) VESC6? by Marc Pflugmann » Fri, 2018-05-25 21:02 |
3 |
by Roger Wolff Thu, 2018-05-31 08:05 |
|
|
How to RC segway Ninebot pro using BALANCE mode? $$ by zmei116 » Sun, 2020-02-23 12:22 |
3 |
by zmei116 Fri, 2020-12-04 00:36 |
|
|
Vesc repair guidances by Booya » Tue, 2020-03-10 17:31 |
3 |
by oschlueter Fri, 2021-09-10 12:10 |
|
|
Why Mosfet and Motor HW temp sensor schematic are different?! by ThierryGTLTS » Sat, 2017-09-09 10:13 |
3 |
by ThierryGTLTS Mon, 2017-09-11 12:50 |
|
|
What is ADC3 used for in VESC6 by Tilman Baumann » Tue, 2018-04-10 11:12 |
3 |
by Gos1 Mon, 2023-06-26 13:56 |
|
|
VESC 6 MkVI HP max current limit by onluckyy » Wed, 2023-11-01 20:08 |
3 |
by lizardmech Tue, 2023-11-14 13:10 |
|
|
Danger to go more than 100% duty cycle during downhill ? by f.damien12 » Thu, 2022-03-24 14:12 |
3 |
by skyline1970 Sat, 2022-03-26 09:29 |
|
|
Built in BLE HD60 not Working by CS » Mon, 2021-08-23 13:21 |
3 |
by frank Thu, 2021-08-26 08:09 |
|
|
Why does the 75/300 have VCC at 3.4V? by TechAUmNu » Tue, 2020-03-31 14:01 |
3 |
by TechAUmNu Wed, 2020-09-02 12:04 |
|
|
Vesc 6 MKIV ? by mchatain » Mon, 2020-05-04 11:43 |
3 |
by maxpla Wed, 2020-06-10 10:04 |
|
|
VESC 75/300 with sin/cos encoder by sajjen » Tue, 2019-11-12 16:16 |
4 |
by marcos_ Sun, 2020-01-19 22:48 |
|
|
VESC 6.4 supplys Arduino over SIGNAL!! by MaxMaker1 » Thu, 2018-05-24 15:02 |
4 |
by frank Mon, 2018-06-04 23:24 |
|
|
Inductance (L) measurement by rahmaev_a_o » Tue, 2018-08-07 10:10 |
4 |
by benjamin Sat, 2019-02-23 10:11 |
|
|
VESC hardware schematics by cromoly » Tue, 2017-11-28 04:44 |
4 |
by ThierryGTLTS Tue, 2017-12-19 14:03 |
|
|
HARDWARE QUESTION: Maximum AC voltage VESC can tolerate? by danvel » Fri, 2018-04-27 15:31 |
4 |
by Roger Wolff Mon, 2018-05-14 22:13 |
|
|
SOLVED - Sensor Voltage Switching on VESC 6 MkVI? by UAMTec » Tue, 2023-10-10 02:25 |
4 |
by tobiokanobi Fri, 2024-10-04 23:26 |
|
|
VCC-GND short by caliber interconnect » Sat, 2022-02-26 13:10 |
4 |
by caliber interconnect Tue, 2022-03-01 10:42 |
|
|
Increasing phase amps beyond 300a on 100-250 by reubarb.scons » Tue, 2022-03-15 07:30 |
4 |
by reubarb.scons Thu, 2022-03-17 22:28 |
|
|
3.3v short. is repair possible? by TZTZ » Sat, 2021-08-21 10:33 |
4 |
by tecnico.solarboat Mon, 2021-12-27 23:31 |
|
|
Are the FOC PID values for discrete or continuous time controllers? by ward » Fri, 2022-01-21 15:55 |
4 |
by Elwin Tue, 2022-01-25 07:48 |
|
|
FSESC 6.6 dual short on 3.3v on 1 side by vic1234 » Thu, 2022-02-17 22:33 |
4 |
by vic1234 Fri, 2022-02-18 17:52 |
|
|
Hall sensor not working by Stupidspencer » Sat, 2019-12-28 20:29 |
4 |
by BeliaEllet Wed, 2021-03-31 17:55 |
Log in to post new content in the forum.
