You are here
VESC Original Hardware
Log in to post new content in the forum.
Topic / Topic starter |
Replies | Last post | |
|---|---|---|---|
|
Trampa 100/250 with Cyc X1 Pro motor by Asi » Mon, 2023-05-22 17:33 |
1 |
by vadicus Thu, 2023-06-01 21:31 |
|
|
Trampa boards online store by jrowe » Tue, 2019-04-16 06:28 |
0 |
by jrowe Tue, 2019-04-16 06:28 |
|
|
Trouble shooting setup by GeoffGuest » Sat, 2020-10-03 06:12 |
0 |
by GeoffGuest Sat, 2020-10-03 06:12 |
|
|
usb is not connecting by asnamp » Wed, 2022-05-18 09:00 |
1 |
by frank Thu, 2022-05-19 17:14 |
|
|
Using ABI Encoders by danielw » Tue, 2018-10-30 14:33 |
1 |
by danielw Wed, 2018-11-07 15:38 |
|
|
VCC-GND short by caliber interconnect » Sat, 2022-02-26 13:10 |
4 |
by caliber interconnect Tue, 2022-03-01 10:42 |
|
|
VESC 100/250 by electricfox » Mon, 2020-01-13 20:23 |
4 |
by vitormhenrique Thu, 2020-02-13 01:12 |
|
|
VESC 100/250 Bluetooth not showing up by JumpinJackFlash » Sun, 2022-10-09 19:03 |
2 |
by JumpinJackFlash Tue, 2022-10-11 17:27 |
|
|
VESC 100/250 won't go full duty cycle by TheBennis » Tue, 2022-06-14 05:33 |
6 |
by TheBennis Tue, 2022-08-02 04:25 |
|
|
VESC 100V 250A - don't reach 50000ERPM by tobiokanobi » Tue, 2022-04-12 19:29 |
6 |
by tobiokanobi Mon, 2022-05-02 19:22 |
|
|
vesc 3.3 or 5v is shorted to GND by fer-bo » Fri, 2021-03-05 14:57 |
1 |
by fer-bo Fri, 2021-03-05 18:24 |
|
|
Vesc 4.10 high amp blocks motor by darowi » Sun, 2024-03-10 18:22 |
1 |
by rafeh1 Fri, 2024-10-11 01:10 |
|
|
VESC 4.12 +5v output by lennarn » Tue, 2020-04-28 15:35 |
2 |
by sandrino Mon, 2023-01-23 16:01 |
|
|
VESC 4.12 - Data loss on power off by da_rul0r » Wed, 2019-08-14 16:43 |
2 |
by da_rul0r Thu, 2019-08-15 08:33 |
|
|
VESC 4.12 Duty is always 110%. Possible short? by tahirali1 » Sun, 2019-10-13 14:22 |
0 |
by tahirali1 Sun, 2019-10-13 14:22 |
|
|
Vesc 4.12 won't connect thru usb by Bergecorp » Sat, 2024-07-06 04:31 |
0 |
by Bergecorp Sat, 2024-07-06 04:31 |
|
|
VESC 4.12 wont connect to pc by stefann » Sun, 2020-03-15 00:42 |
0 |
by stefann Sun, 2020-03-15 00:42 |
|
|
Vesc 6 - Rotorposition control with Encoder AS5047P by Espeya24 » Thu, 2020-12-10 09:01 |
1 |
by kevinagomez Sat, 2024-07-27 20:33 |
|
|
Vesc 6 and encoder connections by eptv » Thu, 2019-10-31 15:46 |
2 |
by ergnmnh Thu, 2023-12-07 13:01 |
|
|
VESC 6 MK IV circuit question by Simmo1337 » Tue, 2022-08-16 23:10 |
0 |
by Simmo1337 Tue, 2022-08-16 23:10 |
|
|
Vesc 6 MKIV ? by mchatain » Mon, 2020-05-04 11:43 |
3 |
by maxpla Wed, 2020-06-10 10:04 |
|
|
VESC 6 MkVI HP max current limit by onluckyy » Wed, 2023-11-01 20:08 |
3 |
by lizardmech Tue, 2023-11-14 13:10 |
|
|
VESC 6 Plus reseting settings and firmware by granstubbe » Fri, 2020-01-10 18:31 |
2 |
by ozcankosar Fri, 2022-11-25 22:18 |
|
|
VESC 6 Schematic Question by mendez » Tue, 2019-02-12 07:11 |
8 |
by frank Thu, 2019-12-05 11:28 |
|
|
VESC 6, astroflight 3215, loosing sync with freewheel by Rouckie » Mon, 2020-05-11 00:22 |
0 |
by Rouckie Mon, 2020-05-11 00:22 |
Log in to post new content in the forum.
