You are here
VESC Original Hardware
Log in to post new content in the forum.
Topic / Topic starter |
Replies | Last post | |
|---|---|---|---|
|
Programming Vesc 4.12 motor spin only in detection mode by DanieleRA » Sun, 2019-07-28 16:29 |
0 |
by DanieleRA Sun, 2019-07-28 16:29 |
|
|
PWM outputs on Hall1 and Hall2 pins by brentfpage » Mon, 2020-08-31 01:32 |
2 |
by mechatronixNick Wed, 2021-01-27 08:53 |
|
|
Servomotor control with VESC6 by Humberto Estrada » Wed, 2019-05-22 16:15 |
0 |
by Humberto Estrada Wed, 2019-05-22 16:15 |
|
|
Setting up a VESC 6 MK IV and need 58.2 voltage fault by warrenhdavis » Fri, 2020-05-22 07:34 |
2 |
by TheFallen Wed, 2020-05-27 08:59 |
|
|
Smoked 3 month old VESC - What did I do wrong? by cjjohnson97 » Thu, 2020-04-16 02:30 |
1 |
by velolac Sun, 2020-08-02 11:27 |
|
|
Spare 5V current for accessories by Pimousse » Mon, 2018-01-08 15:49 |
3 |
by benjamin Wed, 2018-01-24 15:21 |
|
|
Speed Pin from motor into VESC 6+? by dfelz » Tue, 2020-04-07 23:42 |
1 |
by frank Mon, 2020-05-04 14:50 |
|
|
StartUp in OpenLoop with Duty Control really jerky by tobiokanobi » Thu, 2022-09-29 07:22 |
1 |
by frank Thu, 2022-09-29 08:00 |
|
|
switch/toggle between two different engine settings/characteristics by Lasse » Tue, 2020-12-29 23:18 |
1 |
by skyline1970 Sun, 2021-02-07 17:35 |
|
|
Temperature Sensor Dallas DS18B20 by tobiokanobi » Tue, 2022-06-07 10:07 |
2 |
by tobiokanobi Wed, 2022-06-08 15:25 |
|
|
Total dead-time of the MOSFETs ???!! by ThierryGTLTS » Tue, 2017-09-12 17:08 |
6 |
by TechAUmNu Fri, 2018-01-26 10:37 |
|
|
Trampa boards online store by jrowe » Tue, 2019-04-16 06:28 |
0 |
by jrowe Tue, 2019-04-16 06:28 |
|
|
Trouble shooting setup by GeoffGuest » Sat, 2020-10-03 06:12 |
0 |
by GeoffGuest Sat, 2020-10-03 06:12 |
|
|
usb is not connecting by asnamp » Wed, 2022-05-18 09:00 |
1 |
by frank Thu, 2022-05-19 17:14 |
|
|
Using ABI Encoders by danielw » Tue, 2018-10-30 14:33 |
1 |
by danielw Wed, 2018-11-07 15:38 |
|
|
VCC-GND short by caliber interconnect » Sat, 2022-02-26 13:10 |
4 |
by caliber interconnect Tue, 2022-03-01 10:42 |
|
|
VESC 100/250 by electricfox » Mon, 2020-01-13 20:23 |
4 |
by vitormhenrique Thu, 2020-02-13 01:12 |
|
|
VESC 100/250 Bluetooth not showing up by JumpinJackFlash » Sun, 2022-10-09 19:03 |
2 |
by JumpinJackFlash Tue, 2022-10-11 17:27 |
|
|
VESC 100/250 won't go full duty cycle by TheBennis » Tue, 2022-06-14 05:33 |
6 |
by TheBennis Tue, 2022-08-02 04:25 |
|
|
VESC 100V 250A - don't reach 50000ERPM by tobiokanobi » Tue, 2022-04-12 19:29 |
6 |
by tobiokanobi Mon, 2022-05-02 19:22 |
|
|
vesc 3.3 or 5v is shorted to GND by fer-bo » Fri, 2021-03-05 14:57 |
1 |
by fer-bo Fri, 2021-03-05 18:24 |
|
|
VESC 4.12 +5v output by lennarn » Tue, 2020-04-28 15:35 |
2 |
by sandrino Mon, 2023-01-23 16:01 |
|
|
VESC 4.12 - Data loss on power off by da_rul0r » Wed, 2019-08-14 16:43 |
2 |
by da_rul0r Thu, 2019-08-15 08:33 |
|
|
VESC 4.12 Duty is always 110%. Possible short? by tahirali1 » Sun, 2019-10-13 14:22 |
0 |
by tahirali1 Sun, 2019-10-13 14:22 |
|
|
VESC 4.12 wont connect to pc by stefann » Sun, 2020-03-15 00:42 |
0 |
by stefann Sun, 2020-03-15 00:42 |
Log in to post new content in the forum.
