You are here

VESC Original Hardware

Topic / Topic starter Replies Last postsort descending
Normal topic Inductance (L) measurement
by rahmaev_a_o » Tue, 2018-08-07 10:10
4
by benjamin
Sat, 2019-02-23 10:11
Normal topic Trampa boards online store
by jrowe » Tue, 2019-04-16 06:28
0
by jrowe
Tue, 2019-04-16 06:28
Normal topic Servomotor control with VESC6
by Humberto Estrada » Wed, 2019-05-22 16:15
0
by Humberto Estrada
Wed, 2019-05-22 16:15
Normal topic Fault: FAULT_CODE_HIGH_OFFSET_CURRENT_SENSOR_3 on VESC 6
by Jackl » Tue, 2019-05-28 14:48
0
by Jackl
Tue, 2019-05-28 14:48
Normal topic How exactly do I connect a VESC 6.4 to an Arduino Nano?
by MaxMaker1 » Tue, 2018-07-03 23:18
5
by molak
Tue, 2019-06-04 19:39
Normal topic dual VESC battery current
by chris_winkel » Tue, 2019-06-18 15:26
0
by chris_winkel
Tue, 2019-06-18 15:26
Normal topic Programming Vesc 4.12 motor spin only in detection mode
by DanieleRA » Sun, 2019-07-28 16:29
0
by DanieleRA
Sun, 2019-07-28 16:29
Normal topic VESC Hardware
by eschroff » Thu, 2019-07-25 02:38
1
by skyline1970
Wed, 2019-07-31 13:35
Normal topic Hooking up two or more motor drivers  to the same MCU 
by darkclaude » Thu, 2019-06-20 10:02
2
by skyline1970
Wed, 2019-07-31 13:53
Normal topic VESC 4.12 - Data loss on power off
by da_rul0r » Wed, 2019-08-14 16:43
2
by da_rul0r
Thu, 2019-08-15 08:33
Normal topic VESC 75/300 current noise / losing sync?
by ezonca » Thu, 2019-10-03 23:06
2
by benjamin
Thu, 2019-10-10 07:56
Normal topic fault_code_high_offset_current_sensor_1
by Enak » Thu, 2019-10-10 02:48
2
by Enak
Fri, 2019-10-11 01:24
Normal topic VESC 4.12 Duty is always 110%. Possible short?
by tahirali1 » Sun, 2019-10-13 14:22
0
by tahirali1
Sun, 2019-10-13 14:22
Normal topic Driving two motors with 75/300
by cmarc » Wed, 2019-10-16 17:32
1
by benjamin
Fri, 2019-10-18 10:37
Normal topic 75/300 NRF Pairing
by eptv » Sat, 2019-10-12 14:47
3
by frank
Thu, 2019-12-05 11:22
Normal topic VESC 6 Schematic Question
by mendez » Tue, 2019-02-12 07:11
8
by frank
Thu, 2019-12-05 11:28
Normal topic VESC design specification, manual
by velolac » Thu, 2020-01-02 15:54
1
by velolac
Sat, 2020-01-11 00:05
Normal topic VESC 75/300 with sin/cos encoder
by sajjen » Tue, 2019-11-12 16:16
4
by marcos_
Sun, 2020-01-19 22:48
Normal topic Controlling multiple VESC over SPI
by ttufuor » Mon, 2019-11-18 04:37
2
by Danny Bokma
Fri, 2020-01-24 18:29
Normal topic Choosing Motor Encoder for VESC
by VRdublove » Fri, 2020-01-24 18:51
0
by VRdublove
Fri, 2020-01-24 21:44
Normal topic Power switch on VESCT6+ (MK3)
by henry10210 » Thu, 2019-12-26 00:47
8
by henry10210
Tue, 2020-02-11 15:48
Normal topic VESC 100/250
by electricfox » Mon, 2020-01-13 20:23
4
by vitormhenrique
Thu, 2020-02-13 01:12
Normal topic VESC WAND
by vitormhenrique » Sun, 2020-02-16 19:04
0
by vitormhenrique
Sun, 2020-02-16 19:26
Normal topic Iron less Axialflux Motor
by tobiokanobi » Sat, 2019-03-30 12:11
6
by kaanozgen
Wed, 2020-02-26 11:42
Normal topic Vesc 75/300 burned
by electricfox » Sat, 2020-02-15 22:35
8
by pf26
Fri, 2020-03-06 09:49
New posts
No new posts
Hot topic with new posts
Hot topic without new posts
Sticky topic
Locked topic
Subscribe to RSS - VESC Original Hardware