You are here
VESC Original Hardware
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Vesc motor resistance value by HiandHello » Wed, 2023-02-15 07:45 |
2 |
by HiandHello Wed, 2023-02-15 22:57 |
|
|
Ground Housing VESC by T18m26 » Mon, 2023-04-17 16:25 |
2 |
by T18m26 Thu, 2023-04-27 08:28 |
|
|
VESC MAXIM+120 Reverse Button by michael.jahrer » Wed, 2026-04-22 21:32 |
2 |
by michael.jahrer Sun, 2026-04-26 18:56 |
|
|
Change sensor voltage on latest VESC 75/300 MK IV by R04 » Sun, 2024-01-28 21:22 |
2 |
by frank Fri, 2024-02-23 15:39 |
|
|
Charging through phase wires by jesusc » Mon, 2021-01-18 21:14 |
2 |
by jesusc Thu, 2021-06-03 02:17 |
|
|
optimizing the set up to reduce mosfet heating by tromes » Tue, 2020-06-16 02:48 |
2 |
by TechAUmNu Sun, 2020-08-02 15:06 |
|
|
VESC 75/300 as generator inverter troubleshooting by Renco » Thu, 2020-06-18 13:10 |
2 |
by Renco Wed, 2020-06-24 08:50 |
|
|
VESC 75 300 R2 - correct battery conection by SafrdA » Fri, 2021-04-30 13:13 |
2 |
by frank Wed, 2021-05-26 11:19 |
|
|
VESC 75/250 v 75/300? by AliBarrett10 » Tue, 2021-07-06 19:50 |
2 |
by Ht Tue, 2021-10-12 07:08 |
|
|
PWM outputs on Hall1 and Hall2 pins by brentfpage » Mon, 2020-08-31 01:32 |
2 |
by mechatronixNick Wed, 2021-01-27 08:53 |
|
|
VESC 75 precharge by wagner » Fri, 2020-09-18 22:16 |
2 |
by wagner Tue, 2020-09-22 16:01 |
|
|
How to communication with arduino on vesc via can by yuri12 » Tue, 2022-02-08 13:34 |
2 |
by Craig_Gault Mon, 2023-02-27 13:20 |
|
|
Hooking up two or more motor drivers to the same MCU by darkclaude » Thu, 2019-06-20 10:02 |
2 |
by skyline1970 Wed, 2019-07-31 13:53 |
|
|
Need advice : repair , vesc 4.12, vesc 6.4 or wait ? by frameto » Mon, 2017-11-20 21:57 |
2 |
by frameto Wed, 2017-11-22 22:01 |
|
|
VESC 4.12 - Data loss on power off by da_rul0r » Wed, 2019-08-14 16:43 |
2 |
by da_rul0r Thu, 2019-08-15 08:33 |
|
|
fault_code_high_offset_current_sensor_1 by Enak » Thu, 2019-10-10 02:48 |
2 |
by Enak Fri, 2019-10-11 01:24 |
|
|
HW 4.12 USB Device Descriptor Failed-> Red light flashed on start by MTBVASEY » Wed, 2018-04-04 11:06 |
2 |
by MTBVASEY Wed, 2018-04-04 22:24 |
|
|
Vesc 6 and encoder connections by eptv » Thu, 2019-10-31 15:46 |
2 |
by ergnmnh Thu, 2023-12-07 13:01 |
|
|
Mechanical dimensions of VESC 6 by ufechner » Sat, 2018-04-28 19:01 |
2 |
by TechAUmNu Mon, 2018-04-30 22:28 |
|
|
Controlling multiple VESC over SPI by ttufuor » Mon, 2019-11-18 04:37 |
2 |
by Danny Bokma Fri, 2020-01-24 18:29 |
|
|
WAND -Joystick faulty- by chris_winkel » Wed, 2022-03-23 17:53 |
2 |
by chris_winkel Mon, 2022-03-28 11:14 |
|
|
Temperature Sensor Dallas DS18B20 by tobiokanobi » Tue, 2022-06-07 10:07 |
2 |
by tobiokanobi Wed, 2022-06-08 15:25 |
|
|
Vesc Express show up as "Serial ESP32" when connecting to USB. by rikard.wildare@... » Tue, 2025-05-13 18:34 |
2 |
by zzSkateboards Fri, 2025-07-18 09:33 |
|
|
VESC 4.12 +5v output by lennarn » Tue, 2020-04-28 15:35 |
2 |
by sandrino Mon, 2023-01-23 16:01 |
|
|
Setting up a VESC 6 MK IV and need 58.2 voltage fault by warrenhdavis » Fri, 2020-05-22 07:34 |
2 |
by thefallen Wed, 2020-05-27 08:59 |
Log in to post new content in the forum.
