You are here
VESC Firmware
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
error firmware BMS by Sebastiangeitne... » Mon, 2022-08-15 21:36 |
1 |
by Sebastiangeitne... Thu, 2022-08-18 12:26 |
|
|
Connexion by Barange » Sat, 2022-08-20 20:32 |
1 |
by jose carceller Sun, 2022-08-21 00:32 |
|
|
BLDC switching frequency by tuloski » Wed, 2018-09-19 13:18 |
1 |
by bauck Tue, 2020-11-17 17:08 |
|
|
Will voltage offset on phase cause tracking to get wrong position? by TechAUmNu » Wed, 2018-01-17 18:14 |
1 |
by TechAUmNu Wed, 2018-01-17 21:42 |
|
|
Wear os by Juozas » Tue, 2020-06-23 11:18 |
1 |
by hexakopter Tue, 2020-06-23 19:10 |
|
|
Requesting VESC fault codes via UART by spork » Fri, 2020-06-26 21:52 |
1 |
by f.damien12 Sun, 2022-04-03 18:27 |
|
|
Hall sensor detection failed (AWD setup) by frameto » Tue, 2018-10-02 22:02 |
1 |
by ronmotor Tue, 2020-10-27 02:20 |
|
|
VESC 6 plus working but no servo response by saspragkathos » Mon, 2020-06-29 17:28 |
1 |
by Shreeram2311 Tue, 2025-05-06 02:44 |
|
|
firmware too old! by ad_brad » Sun, 2018-10-14 18:33 |
1 |
by arvidb Sun, 2018-10-14 19:21 |
|
|
3.64 can_scan breaks with ppm enabled. by fessyfoo » Fri, 2019-12-20 20:40 |
1 |
by fessyfoo Sun, 2019-12-22 03:44 |
|
|
VESC Control over NRF by Christian » Tue, 2018-03-27 14:42 |
1 |
by m.juan Wed, 2018-07-04 13:44 |
|
|
vesc on stm32_discovery not saving motor/app configs in non volatile memory by Teslafly » Thu, 2020-02-06 01:23 |
1 |
by imbizo Thu, 2020-10-22 14:54 |
|
|
Limiting of throttle curves has no effect by Ackmaniac » Thu, 2017-09-07 17:21 |
1 |
by frank Tue, 2017-09-19 09:35 |
|
|
Problems with flashing firmware to FLIPSKY ESC by xx11xx » Wed, 2019-08-14 18:10 |
1 |
by kinzma Tue, 2019-08-20 07:56 |
|
|
Firmware 3.29 hardware 4.12 , 0.5mOhm shunts by brushlessdevil » Sun, 2017-10-15 19:28 |
1 |
by benjamin Thu, 2017-10-19 15:15 |
|
|
FOC alignment and startup by nami1216 » Mon, 2020-03-30 10:40 |
1 |
by kaanozgen Tue, 2020-03-31 10:57 |
|
|
Custom App - Set Motor Speed by CTSchorsch » Fri, 2019-10-25 11:22 |
1 |
by bayetan Wed, 2022-10-12 16:05 |
|
|
[Contributing][FOC] injected ADC and code clarity by Guillaume227 » Fri, 2017-12-15 18:00 |
1 |
by Roger Wolff Sat, 2017-12-16 13:21 |
|
|
VESC 6.0 Hardware Shows Up As HW 410 in VESC-Tool by FWachter » Thu, 2017-12-21 20:51 |
1 |
by wdaehn Fri, 2017-12-22 08:22 |
|
|
Current sense SNA/SPA swapped. Where to adjust the code? by shaman » Fri, 2019-11-08 14:51 |
1 |
by Eric Fri, 2019-11-15 11:49 |
|
|
Flipsky 75200 ALU not booting up by Metastasis » Wed, 2023-09-20 15:45 |
2 |
by B1996 Mon, 2024-10-28 22:06 |
|
|
FSESC 75100 Pro V2 W/ ALUMINUM by drstein99 » Tue, 2025-08-26 23:02 |
2 |
by CRTZ Wed, 2025-12-17 14:16 |
|
|
FOC_Openloop terminal command via CAN? by Jackl » Mon, 2024-01-15 10:09 |
2 |
by Jackl Sun, 2024-03-17 21:27 |
|
|
Mini FSESC4.20 firmware bin file by pinkpanther » Thu, 2021-08-19 11:44 |
2 |
by frank Mon, 2021-08-23 09:42 |
|
|
brake inhibit input by kylerlaird » Wed, 2021-01-20 23:35 |
2 |
by isamilner Tue, 2021-03-02 09:26 |
Log in to post new content in the forum.
