You are here
VESC Firmware
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
VESC tool firmware of 256KBytes by Arthur00 » Sat, 2022-12-03 20:57 |
1 |
by skyline1970 Sun, 2022-12-04 13:28 |
|
|
re-scaling CAN setDUTY CYCLE to -1 to 1 instead of 0 to 1 by a.dahhak » Fri, 2020-03-06 11:09 |
1 |
by a.dahhak Mon, 2020-03-09 10:38 |
|
|
How Update firmware vesc 6.41 with broken micro USB fw 3.40? by adrian210188 » Thu, 2020-03-12 01:18 |
1 |
by Pimousse Sat, 2020-03-21 13:01 |
|
|
UAVCAN v0 actuator message features by Henrik1 » Sat, 2020-03-14 19:00 |
1 |
by goocare Tue, 2020-03-24 10:15 |
|
|
VESC6 current and duty cycle scale problem? by henry10210 » Sun, 2020-03-29 22:34 |
1 |
by mansi712 Tue, 2024-10-01 12:48 |
|
|
Spin the motor and stop at a set tachometer index by jchillerup » Tue, 2019-12-10 12:29 |
1 |
by frank Wed, 2019-12-11 14:51 |
|
|
MK3 branch in bldc repo? by henry10210 » Tue, 2019-12-31 23:49 |
1 |
by Teslafly Thu, 2020-02-06 21:22 |
|
|
Fw 4.01 potential issue by Joeshaw » Sun, 2020-03-01 23:15 |
1 |
by Pimousse Sat, 2020-03-21 13:10 |
|
|
Focbox by macglen » Wed, 2024-03-27 22:45 |
1 |
by dpeinado Mon, 2024-04-15 17:51 |
|
|
Change the direction of motor when using PPM and "Current no reverse with brake"? by Kokonenen » Mon, 2023-04-24 13:41 |
1 |
by tokerodev Thu, 2025-08-21 11:10 |
|
|
PPM over CAN by joeker24 » Mon, 2023-07-03 11:15 |
1 |
by tonymillion Wed, 2023-07-12 18:28 |
|
|
ADC and UART app - input priorities? by DaRho » Mon, 2023-07-17 17:01 |
1 |
by DaRho Tue, 2023-07-18 17:11 |
|
|
Help needed VESC - Update missed? by JUST1975 » Tue, 2024-11-26 11:43 |
1 |
by JUST1975 Tue, 2024-11-26 11:53 |
|
|
Lisp script detaches both ADC by dannydnl » Fri, 2023-11-03 16:06 |
1 |
by dannydnl Fri, 2023-11-03 17:58 |
|
|
VESC TRAMPA NRF BLE firmware question and feature request by Spaceman » Sat, 2024-01-06 06:47 |
1 |
by Spaceman Sat, 2024-01-27 08:07 |
|
|
Firmware 6 Issues by Gos1 » Fri, 2024-01-26 10:39 |
1 |
by Ai Fri, 2024-05-31 07:05 |
|
|
Firmware Compatibility Issue with Custom 75_300 Based Hardware by kevin458 » Wed, 2024-02-28 19:55 |
1 |
by kevin458 Wed, 2024-02-28 20:36 |
|
|
Add SPI encoder reading (in addition of the hall sensor) by Mounir » Fri, 2023-03-03 16:04 |
1 |
by frank Wed, 2023-03-15 13:58 |
|
|
Limiting of throttle curves has no effect by Ackmaniac » Thu, 2017-09-07 17:21 |
1 |
by frank Tue, 2017-09-19 09:35 |
|
|
Firmware 3.29 hardware 4.12 , 0.5mOhm shunts by brushlessdevil » Sun, 2017-10-15 19:28 |
1 |
by benjamin Thu, 2017-10-19 15:15 |
|
|
[Contributing][FOC] injected ADC and code clarity by Guillaume227 » Fri, 2017-12-15 18:00 |
1 |
by Roger Wolff Sat, 2017-12-16 13:21 |
|
|
VESC 6.0 Hardware Shows Up As HW 410 in VESC-Tool by FWachter » Thu, 2017-12-21 20:51 |
1 |
by wdaehn Fri, 2017-12-22 08:22 |
|
|
BLDC switching frequency by tuloski » Wed, 2018-09-19 13:18 |
1 |
by bauck Tue, 2020-11-17 17:08 |
|
|
Will voltage offset on phase cause tracking to get wrong position? by TechAUmNu » Wed, 2018-01-17 18:14 |
1 |
by TechAUmNu Wed, 2018-01-17 21:42 |
|
|
Hall sensor detection failed (AWD setup) by frameto » Tue, 2018-10-02 22:02 |
1 |
by ronmotor Tue, 2020-10-27 02:20 |
Log in to post new content in the forum.
