You are here
VESC Firmware
Log in to post new content in the forum.
Topic / Topic starter | Replies | Last post | |
---|---|---|---|
how to build new bin code on win10 by yiannis » Wed, 2021-09-15 21:05 |
1 |
by skyline1970 Fri, 2021-10-29 11:54 |
|
Changing out timer 5 in timer.c by Teslafly » Fri, 2019-07-12 20:05 |
1 |
by Teslafly Fri, 2019-07-12 21:52 |
|
about Hall count (tacho value) problem by sirino » Wed, 2021-02-17 02:35 |
1 |
by sirino Fri, 2021-02-19 08:31 |
|
PPM Over limit settings. by marto » Thu, 2019-03-07 05:35 |
1 |
by marto Thu, 2019-03-07 08:36 |
|
position control with vesc firmware by erhan » Mon, 2020-10-12 16:03 |
1 |
by Kent Tabor Sun, 2020-10-18 14:39 |
|
VESC Firmware update not working by timhermanson94 » Wed, 2019-07-31 18:42 |
1 |
by skyline1970 Fri, 2019-08-02 15:22 |
|
VESC Firmware Change, No Longer Connects by wj311 » Wed, 2021-03-10 22:40 |
1 |
by benjamin Thu, 2021-03-18 10:52 |
|
Vesc bricked with custom app, no SWD by stexo » Sat, 2020-10-17 18:44 |
1 |
by Bill Somerville Fri, 2020-11-06 23:30 |
|
Spin the motor and stop at a set tachometer index by jchillerup » Tue, 2019-12-10 12:29 |
1 |
by frank Wed, 2019-12-11 14:51 |
|
REVERSE FAIL in ADC_CURRENT_REV_BUTTON_BRAKE_ADC by dk-odense » Tue, 2019-12-17 15:45 |
1 |
by benjamin Fri, 2019-12-27 23:09 |
|
MK3 branch in bldc repo? by henry10210 » Tue, 2019-12-31 23:49 |
1 |
by Teslafly Thu, 2020-02-06 21:22 |
|
Fw 4.01 potential issue by Joeshaw » Sun, 2020-03-01 23:15 |
1 |
by Pimousse Sat, 2020-03-21 13:10 |
|
re-scaling CAN setDUTY CYCLE to -1 to 1 instead of 0 to 1 by a.dahhak » Fri, 2020-03-06 11:09 |
1 |
by a.dahhak Mon, 2020-03-09 10:38 |
|
How Update firmware vesc 6.41 with broken micro USB fw 3.40? by adrian210188 » Thu, 2020-03-12 01:18 |
1 |
by Pimousse Sat, 2020-03-21 13:01 |
|
UAVCAN v0 actuator message features by Henrik1 » Sat, 2020-03-14 19:00 |
1 |
by goocare Tue, 2020-03-24 10:15 |
|
firmware too old! by ad_brad » Sun, 2018-10-14 18:33 |
1 |
by arvidb Sun, 2018-10-14 19:21 |
|
VESC Control over NRF by Christian » Tue, 2018-03-27 14:42 |
1 |
by m.juan Wed, 2018-07-04 13:44 |
|
Limiting of throttle curves has no effect by Ackmaniac » Thu, 2017-09-07 17:21 |
1 |
by frank Tue, 2017-09-19 09:35 |
|
Firmware 3.29 hardware 4.12 , 0.5mOhm shunts by brushlessdevil » Sun, 2017-10-15 19:28 |
1 |
by benjamin Thu, 2017-10-19 15:15 |
|
[Contributing][FOC] injected ADC and code clarity by Guillaume227 » Fri, 2017-12-15 18:00 |
1 |
by Roger Wolff Sat, 2017-12-16 13:21 |
|
VESC 6.0 Hardware Shows Up As HW 410 in VESC-Tool by FWachter » Thu, 2017-12-21 20:51 |
1 |
by wdaehn Fri, 2017-12-22 08:22 |
|
BLDC switching frequency by tuloski » Wed, 2018-09-19 13:18 |
1 |
by bauck Tue, 2020-11-17 17:08 |
|
Will voltage offset on phase cause tracking to get wrong position? by TechAUmNu » Wed, 2018-01-17 18:14 |
1 |
by TechAUmNu Wed, 2018-01-17 21:42 |
|
Hall sensor detection failed (AWD setup) by frameto » Tue, 2018-10-02 22:02 |
1 |
by ronmotor Tue, 2020-10-27 02:20 |
|
Add SPI encoder reading (in addition of the hall sensor) by Mounir » Fri, 2023-03-03 16:04 |
1 |
by frank Wed, 2023-03-15 13:58 |
Log in to post new content in the forum.