You are here
VESC Firmware
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Regenerative Braking by silvatma » Wed, 2021-05-26 00:38 |
0 |
by silvatma Wed, 2021-05-26 00:38 |
|
|
Use Mutexes within the ppm app by talabo » Thu, 2021-07-15 12:25 |
0 |
by talabo Thu, 2021-07-15 12:25 |
|
|
75/300 R2 FW higher than 3.62 ? it is possible? by Lasse » Sat, 2020-12-26 20:34 |
0 |
by Lasse Sat, 2020-12-26 20:34 |
|
|
Regarding code documentation by hiddenzed » Mon, 2021-02-08 12:40 |
0 |
by hiddenzed Mon, 2021-02-08 12:40 |
|
|
Change some VESC configurations by nltb » Fri, 2020-09-11 13:39 |
0 |
by nltb Fri, 2020-09-11 13:39 |
|
|
Current sign varies between motors by vadimz » Fri, 2022-08-26 11:24 |
0 |
by vadimz Fri, 2022-08-26 11:24 |
|
|
The engine stopped spinning after updating firmware This topic has been moved to "VESC Tool" (View topic) |
|||
|
75300 r2 v5.3 by Oscarmanassan » Tue, 2022-09-27 14:23 |
0 |
by Oscarmanassan Tue, 2022-09-27 14:23 |
|
|
VESC firmware to programmable Sabvoton ml60 controller. by Maciejwarloch » Tue, 2022-03-08 13:25 |
0 |
by Maciejwarloch Tue, 2022-03-08 13:25 |
|
|
Sending Negative Values to VESC over CAN bus by olivierabristol » Fri, 2022-03-25 09:11 |
0 |
by olivierabristol Fri, 2022-03-25 09:13 |
|
|
CAN sends error frame by dgarciasoto » Wed, 2022-04-27 07:11 |
0 |
by dgarciasoto Wed, 2022-04-27 07:11 |
|
|
Dual Vesc reading second wheel RPM by rdavenport3 » Tue, 2022-05-03 15:32 |
0 |
by rdavenport3 Tue, 2022-05-03 15:32 |
|
|
Request for Example: Can communication with Libcanard by WoofyBunny » Fri, 2022-05-13 03:44 |
0 |
by WoofyBunny Fri, 2022-05-13 03:45 |
|
|
Move FAULT pin to GPIOD_PIN2 by CTSchorsch » Tue, 2018-09-04 10:13 |
0 |
by CTSchorsch Tue, 2018-09-04 10:13 |
|
|
VESC hardware interrupt pins by gpzhao » Sun, 2018-04-01 10:47 |
0 |
by gpzhao Sun, 2018-04-01 10:50 |
|
|
Cannot upgrade firmware by greensightag.com » Fri, 2018-04-27 02:32 |
0 |
by greensightag.com Fri, 2018-04-27 02:34 |
|
|
PWM length not correctly measured by ufechner » Tue, 2018-06-05 11:45 |
0 |
by ufechner Tue, 2018-06-05 11:45 |
|
|
PID Speed Control code....for NRF by Dimitri » Tue, 2017-10-03 07:16 |
0 |
by Dimitri Tue, 2017-10-03 07:18 |
|
|
Problem after flash fw 3.38 detection faild dont spin by kataklysm_9090 » Tue, 2018-06-19 22:48 |
0 |
by kataklysm_9090 Tue, 2018-06-19 22:48 |
|
|
Help with Focbox firmware / bootloader upgrade [VESC TOOL] by Enigmacpl03 » Thu, 2017-10-05 17:21 |
0 |
by Enigmacpl03 Thu, 2017-10-05 17:21 |
|
|
Vesc Tool cannot detect firmware by MARK EVERITT » Sat, 2018-06-30 18:36 |
0 |
by MARK EVERITT Sat, 2018-06-30 18:36 |
|
|
USB connection problem by Ironman223 » Sat, 2019-10-12 13:53 |
0 |
by Ironman223 Sat, 2019-10-12 13:53 |
|
|
Ethernet support by selfservice » Sun, 2020-03-22 19:56 |
0 |
by selfservice Sun, 2020-03-22 19:56 |
|
|
physical meaning of current KI and current KP coefficients by ExiD » Tue, 2019-10-15 16:38 |
0 |
by ExiD Tue, 2019-10-15 16:38 |
|
|
Unable to flash firmware to VESC using OpenOCD by Bayne » Fri, 2019-10-25 02:34 |
0 |
by Bayne Fri, 2019-10-25 02:35 |
|
Log in to post new content in the forum.
