You are here
VESC Firmware
Log in to post new content in the forum.
Topic / Topic starter |
Replies | Last post | |
|---|---|---|---|
|
Sticky:
VESC 75/300 R2 with R1 Firmware by frank » Thu, 2019-11-28 09:39 |
1 |
by Henque19 Sat, 2021-04-24 22:48 |
|
|
"Porting" VESC FW to physically smaller device? by Jackl » Fri, 2020-03-13 14:04 |
2 |
by Jackl Mon, 2020-03-16 14:52 |
|
|
(solved) Configuration smooth motordirection change by horak2084 » Mon, 2019-02-25 20:44 |
9 |
by fpagac Sat, 2020-04-25 17:17 |
|
|
(SOLVED) I2C, change pins by CTSchorsch » Mon, 2020-05-25 07:59 |
6 |
by woodmastr Tue, 2023-06-06 15:57 |
|
|
(Watchdog) - Resets with multipole engine. by edilger » Mon, 2023-06-26 12:33 |
0 |
by edilger Mon, 2023-06-26 12:33 |
|
|
100_250_mkiii official release by hugros » Mon, 2023-08-07 15:40 |
0 |
by hugros Mon, 2023-08-07 15:40 |
|
|
200kHz PWM by c10yas » Sun, 2019-09-22 17:06 |
2 |
by Eric Thu, 2019-11-07 18:09 |
|
|
3.64 can_scan breaks with ppm enabled. by fessyfoo » Fri, 2019-12-20 20:40 |
1 |
by fessyfoo Sun, 2019-12-22 03:44 |
|
|
3rd harmonic injection or SVPWM/ Midpoint Clamp for FOC by ufechner » Sat, 2018-04-21 06:05 |
3 |
by arvidb Tue, 2018-05-08 16:35 |
|
|
75/300 R2 FW higher than 3.62 ? it is possible? by Lasse » Sat, 2020-12-26 20:34 |
0 |
by Lasse Sat, 2020-12-26 20:34 |
|
|
75300 r2 v5.3 by Oscarmanassan » Tue, 2022-09-27 14:27 |
7 |
by rogerio Sun, 2023-05-28 17:06 |
|
|
75300 r2 v5.3 by Oscarmanassan » Tue, 2022-09-27 14:23 |
0 |
by Oscarmanassan Tue, 2022-09-27 14:23 |
|
|
about Hall count (tacho value) problem by sirino » Wed, 2021-02-17 02:35 |
1 |
by sirino Fri, 2021-02-19 08:31 |
|
|
Accidentally Bricked MakerX Go-Foc D60 by masong » Mon, 2023-04-24 07:41 |
0 |
by masong Tue, 2023-04-25 03:20 |
|
|
ADC and UART app - input priorities? by DaRho » Mon, 2023-07-17 17:01 |
1 |
by DaRho Tue, 2023-07-18 17:11 |
|
|
ADC EBike Throttle by Dmitry » Sun, 2020-07-26 22:33 |
0 |
by Dmitry Sun, 2020-07-26 22:33 |
|
|
ADC modified app, problem with braking by dpeinado » Wed, 2022-06-22 19:30 |
4 |
by 261122 Mon, 2022-07-04 20:50 |
|
|
ADC Vector Arrangement by javmarina » Sun, 2019-12-29 14:32 |
3 |
by CTSchorsch Thu, 2020-05-14 22:34 |
|
|
ADC2 - I just can’t figure it out by mnchvgs79 » Fri, 2023-10-27 02:21 |
0 |
by mnchvgs79 Fri, 2023-10-27 02:21 |
|
|
Add serial port by CTSchorsch » Wed, 2019-08-14 15:30 |
0 |
by CTSchorsch Wed, 2019-08-14 15:30 |
|
|
Add SPI encoder reading (in addition of the hall sensor) by Mounir » Fri, 2023-03-03 16:04 |
1 |
by frank Wed, 2023-03-15 13:58 |
|
|
adding PAS feature on Firmware 5.01 by marc426 » Sat, 2023-07-15 23:56 |
1 |
by marc426 Sun, 2023-07-16 15:25 |
|
|
Adding support for three phase shunts... by Roger Wolff » Wed, 2017-11-08 16:03 |
3 |
by georpo Tue, 2018-03-13 14:34 |
|
|
adiv5.h adiv5_dp_abort function confusion by dsppower » Sun, 2022-05-08 19:26 |
0 |
by dsppower Sun, 2022-05-08 19:26 |
|
|
AHRS yaw drifting by henry10210 » Sun, 2020-02-09 01:13 |
0 |
by henry10210 Sun, 2020-02-09 01:13 |
Log in to post new content in the forum.
