You are here
VESC Firmware
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Modifications Needed for Custom Dual Motor ESC for 3S Operation by NK-108 » Mon, 2025-12-15 18:27 |
0 |
by NK-108 Mon, 2025-12-15 18:27 |
|
|
Low-Speed Hall Interpolation Performance Issues by cpaterson » Tue, 2026-01-27 03:42 |
0 |
by cpaterson Tue, 2026-01-27 03:42 |
|
|
Compiled Firmware in limited mode by sirAnton » Sat, 2026-03-21 10:13 |
0 |
by sirAnton Sat, 2026-03-21 10:13 |
|
|
75300 r2 v5.3 by Oscarmanassan » Tue, 2022-09-27 14:23 |
0 |
by Oscarmanassan Tue, 2022-09-27 14:23 |
|
|
VESC firmware to programmable Sabvoton ml60 controller. by Maciejwarloch » Tue, 2022-03-08 13:25 |
0 |
by Maciejwarloch Tue, 2022-03-08 13:25 |
|
|
Hard faults in mcpwm_foc.c? by vesc_fault » Thu, 2019-01-03 07:00 |
0 |
by vesc_fault Thu, 2019-01-03 07:20 |
|
|
Sending Negative Values to VESC over CAN bus by olivierabristol » Fri, 2022-03-25 09:11 |
0 |
by olivierabristol Fri, 2022-03-25 09:13 |
|
|
Serial Communication in Non-RT System by Jack_Li » Fri, 2019-07-05 15:58 |
0 |
by Jack_Li Fri, 2019-07-05 15:58 |
|
|
Travis CI by paltatech » Tue, 2019-01-29 00:57 |
0 |
by paltatech Tue, 2019-01-29 00:57 |
|
|
Reassign status LED ports by Filcas » Fri, 2019-07-19 17:17 |
0 |
by Filcas Fri, 2019-07-19 17:17 |
|
|
Dual Vesc reading second wheel RPM by rdavenport3 » Tue, 2022-05-03 15:32 |
0 |
by rdavenport3 Tue, 2022-05-03 15:32 |
|
|
Request for Example: Can communication with Libcanard by WoofyBunny » Fri, 2022-05-13 03:44 |
0 |
by WoofyBunny Fri, 2022-05-13 03:45 |
|
|
Custom App: Motor dont stop by CTSchorsch » Fri, 2019-03-22 13:43 |
0 |
by CTSchorsch Fri, 2019-03-22 13:43 |
|
|
what do you guys think about this "curr_samp_volt "? by jem » Thu, 2019-08-08 14:45 |
0 |
by jem Thu, 2019-08-08 14:45 |
|
|
Add serial port by CTSchorsch » Wed, 2019-08-14 15:30 |
0 |
by CTSchorsch Wed, 2019-08-14 15:30 |
|
|
VESC_default_no_hw_limits by chris-H » Tue, 2019-04-16 17:42 |
0 |
by chris-H Tue, 2019-04-16 17:42 |
|
|
Is COMM_GET_VALUES working on 3.56 fw 410 ? by cnd » Tue, 2019-05-14 17:10 |
0 |
by cnd Tue, 2019-05-14 17:10 |
|
|
Write Motor Configuration - not working by acherpil » Tue, 2018-12-04 10:23 |
0 |
by acherpil Tue, 2018-12-04 16:43 |
|
|
Current sign varies between motors by vadimz » Fri, 2022-08-26 11:24 |
0 |
by vadimz Fri, 2022-08-26 11:24 |
|
|
The engine stopped spinning after updating firmware This topic has been moved to "VESC Tool" (View topic) |
|||
|
Fan PWM output by galp » Wed, 2018-12-05 10:28 |
0 |
by galp Wed, 2018-12-05 10:28 |
|
|
PT1000 on HW 4.12 by nickk » Tue, 2018-12-18 09:49 |
0 |
by nickk Tue, 2018-12-18 09:49 |
|
|
Dual VESC Firmware OTA update from mobile app help by A2 » Wed, 2020-06-24 20:05 |
0 |
by A2 Wed, 2020-06-24 20:05 |
|
|
Firmware Updating to run X2 Pro remote for VESC6.6 by Caddy » Sat, 2020-06-27 19:30 |
0 |
by Caddy Sat, 2020-06-27 19:30 |
|
|
ADC EBike Throttle by Dmitry » Sun, 2020-07-26 22:33 |
0 |
by Dmitry Sun, 2020-07-26 22:33 |
|
Log in to post new content in the forum.
