You are here
VESC Firmware
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Va, Vb, Vc voltages sampling by masifsr » Sat, 2022-05-14 15:25 |
0 |
by masifsr Sat, 2022-05-14 15:25 |
|
|
How difficult would it be to add code to read an external EEPROM, and deactivate/activate depending on a value by PaulMakesThings » Thu, 2021-11-11 09:55 |
0 |
by PaulMakesThings Thu, 2021-11-11 09:55 |
|
|
Right hardware for FW:60 and FSESC6.6 by alexantosh » Wed, 2021-12-01 19:40 |
0 |
by alexantosh Wed, 2021-12-01 20:19 |
|
|
high side active low and low side active high driver signal setting in firmware. by Spencer.chen » Wed, 2021-12-15 14:00 |
0 |
by Spencer.chen Wed, 2021-12-15 14:04 |
|
|
VESC Remote - Input Deadband setting causing severe input delay as well as changing deadband by agraham » Wed, 2022-07-13 07:41 |
0 |
by agraham Wed, 2022-07-13 07:42 |
|
|
BLDC_SPEED_CONTROL_CURRENT by salviador » Fri, 2022-01-14 16:32 |
0 |
by salviador Fri, 2022-01-14 16:32 |
|
|
TMP100 I2C Sensor by CTSchorsch » Tue, 2020-04-21 15:55 |
0 |
by CTSchorsch Tue, 2020-04-21 15:55 |
|
|
VESC PID by nidhirao » Tue, 2019-12-17 13:56 |
0 |
by nidhirao Tue, 2019-12-17 13:56 |
|
|
Dutycycle set using uart problem by Raja Sharma » Tue, 2020-07-21 21:38 |
0 |
by Raja Sharma Tue, 2020-07-21 21:38 |
|
|
VESC 6 MKIII - Writing Custom Applications using Ubuntu by TanmayP » Wed, 2020-08-05 00:48 |
0 |
by TanmayP Wed, 2020-08-05 00:48 |
|
|
noob question - how to I update FW to 3.66? by brently » Thu, 2020-01-16 02:22 |
0 |
by brently Thu, 2020-01-16 02:22 |
|
|
Problema vesc 6.6 plus by Andres Enrique » Sun, 2020-08-30 00:33 |
0 |
by Andres Enrique Sun, 2020-08-30 00:33 |
|
|
Enabling WS2811 not working by vitormhenrique » Thu, 2020-03-05 03:42 |
0 |
by vitormhenrique Thu, 2020-03-05 03:42 |
|
|
Problems getting Cruise control to run properly with the new wand - dual VESC6 by MaddiQ » Mon, 2019-09-16 19:36 |
0 |
by MaddiQ Mon, 2019-09-16 19:36 |
|
|
mcpwm_foc and mcpwm tutorial by nami1216 » Tue, 2019-10-15 07:12 |
0 |
by nami1216 Tue, 2019-10-15 07:12 |
|
|
VESC ramping problem by andrii619 » Mon, 2020-03-23 21:45 |
0 |
by andrii619 Mon, 2020-03-23 21:45 |
|
|
(Watchdog) - Resets with multipole engine. by edilger » Mon, 2023-06-26 12:33 |
0 |
by edilger Mon, 2023-06-26 12:33 |
|
|
How to update Old Enertion Raptor 2.0 for use VESC and what FW? by quinu » Tue, 2024-10-15 22:01 |
0 |
by quinu Tue, 2024-10-15 22:01 |
|
|
new to vesc having all sorts of problems by Nic.karpik » Mon, 2023-07-24 00:04 |
0 |
by Nic.karpik Mon, 2023-07-24 00:05 |
|
|
about VESC6.4 how to connect to tool? by h1989 » Tue, 2024-11-05 16:40 |
0 |
by h1989 Tue, 2024-11-05 16:40 |
|
|
Phase current limit mismatch by Addy » Tue, 2018-05-22 17:12 |
0 |
by Addy Tue, 2018-05-22 17:12 |
|
|
Flipsky 75100 not running after firmware update by defazioaa » Sat, 2025-03-29 01:33 |
0 |
by defazioaa Sat, 2025-03-29 01:33 |
|
|
servo input by Roger Wolff » Tue, 2018-07-03 07:50 |
0 |
by Roger Wolff Tue, 2018-07-03 07:50 |
|
|
Innotrace X1 motor controller for Bafang m620 UART with VESC firmware by TPEHAK » Tue, 2025-06-10 22:00 |
0 |
by TPEHAK Tue, 2025-06-10 22:03 |
|
|
double post by Spaceman » Sat, 2024-01-06 06:45 |
0 |
by Spaceman Sun, 2024-01-07 09:56 |
Log in to post new content in the forum.
