You are here
VESC Firmware
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
VESC - HIL / DRV8301 SPI - Problems? by mm_iem » Tue, 2022-08-09 12:34 |
1 |
by skyline1970 Thu, 2022-11-24 20:54 |
|
|
firm ware error 75_300 by yuri12 » Wed, 2022-01-19 09:50 |
1 |
by frank Wed, 2022-01-19 13:46 |
|
|
new vesc 6 FW update by Shwepsss » Thu, 2022-01-20 20:26 |
1 |
by Shwepsss Fri, 2022-01-21 15:20 |
|
|
Older VESC BLDC Firmware Version Source Code by Vikram Bhat » Mon, 2022-09-12 03:16 |
1 |
by frank Tue, 2022-09-13 21:09 |
|
|
DRV835x by AdinAck » Thu, 2022-10-20 16:14 |
1 |
by frank Fri, 2022-10-21 13:06 |
|
|
App development and Debug by dpeinado » Fri, 2022-04-01 13:22 |
1 |
by Gatze Sun, 2022-04-24 00:15 |
|
|
Problems Compiling Firmware by LB94 » Tue, 2022-11-29 00:08 |
1 |
by Daniel... Tue, 2023-09-19 20:17 |
|
|
Cannot read data over UART by amalbers01 » Sat, 2022-04-16 05:03 |
1 |
by frank Sat, 2022-04-16 20:06 |
|
|
VESC tool firmware of 256KBytes by Arthur00 » Sat, 2022-12-03 20:57 |
1 |
by skyline1970 Sun, 2022-12-04 13:28 |
|
|
Limiting of throttle curves has no effect by Ackmaniac » Thu, 2017-09-07 17:21 |
1 |
by frank Tue, 2017-09-19 09:35 |
|
|
Firmware 3.29 hardware 4.12 , 0.5mOhm shunts by brushlessdevil » Sun, 2017-10-15 19:28 |
1 |
by benjamin Thu, 2017-10-19 15:15 |
|
|
[Contributing][FOC] injected ADC and code clarity by Guillaume227 » Fri, 2017-12-15 18:00 |
1 |
by Roger Wolff Sat, 2017-12-16 13:21 |
|
|
VESC 6.0 Hardware Shows Up As HW 410 in VESC-Tool by FWachter » Thu, 2017-12-21 20:51 |
1 |
by wdaehn Fri, 2017-12-22 08:22 |
|
|
BLDC switching frequency by tuloski » Wed, 2018-09-19 13:18 |
1 |
by bauck Tue, 2020-11-17 17:08 |
|
|
Will voltage offset on phase cause tracking to get wrong position? by TechAUmNu » Wed, 2018-01-17 18:14 |
1 |
by TechAUmNu Wed, 2018-01-17 21:42 |
|
|
Hall sensor detection failed (AWD setup) by frameto » Tue, 2018-10-02 22:02 |
1 |
by ronmotor Tue, 2020-10-27 02:20 |
|
|
firmware too old! by ad_brad » Sun, 2018-10-14 18:33 |
1 |
by arvidb Sun, 2018-10-14 19:21 |
|
|
VESC Control over NRF by Christian » Tue, 2018-03-27 14:42 |
1 |
by m.juan Wed, 2018-07-04 13:44 |
|
|
mcpwm_set_current VS mcpwm_set_brake_current by stiganielsen » Wed, 2019-09-11 15:40 |
2 |
by mechhead Mon, 2022-02-14 11:04 |
|
|
200kHz PWM by c10yas » Sun, 2019-09-22 17:06 |
2 |
by Eric Thu, 2019-11-07 18:09 |
|
|
VESC Firmware (conf_general.h) by HopeAndWonder » Sat, 2020-05-16 20:44 |
2 |
by judylee Thu, 2020-06-18 11:25 |
|
|
Duty cycle take 95% when motor released by Rarikao » Mon, 2019-12-23 08:57 |
2 |
by agnesnorris Sat, 2020-02-29 03:48 |
|
|
Uploading compiled firmware results in no USB access by Count1310 » Sat, 2020-08-08 14:45 |
2 |
by ibarretos Sun, 2020-08-30 13:34 |
|
|
Driving Synchronous reluctance motor using VESC by mmandar90 » Fri, 2023-04-21 14:34 |
2 |
by Ganzey Thu, 2023-04-27 00:17 |
|
|
vesc disconnected during detection by TonyYuan » Mon, 2023-06-26 09:17 |
2 |
by powerpedalph Thu, 2025-04-24 07:51 |
Log in to post new content in the forum.
