You are here
VESC Firmware
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
re-scaling CAN setDUTY CYCLE to -1 to 1 instead of 0 to 1 by a.dahhak » Fri, 2020-03-06 11:09 |
1 |
by a.dahhak Mon, 2020-03-09 10:38 |
|
|
How Update firmware vesc 6.41 with broken micro USB fw 3.40? by adrian210188 » Thu, 2020-03-12 01:18 |
1 |
by Pimousse Sat, 2020-03-21 13:01 |
|
|
UAVCAN v0 actuator message features by Henrik1 » Sat, 2020-03-14 19:00 |
1 |
by goocare Tue, 2020-03-24 10:15 |
|
|
VESC6 current and duty cycle scale problem? by henry10210 » Sun, 2020-03-29 22:34 |
1 |
by mansi712 Tue, 2024-10-01 12:48 |
|
|
Spin the motor and stop at a set tachometer index by jchillerup » Tue, 2019-12-10 12:29 |
1 |
by frank Wed, 2019-12-11 14:51 |
|
|
error firmware BMS by Sebastiangeitne... » Mon, 2022-08-15 21:36 |
1 |
by Sebastiangeitne... Thu, 2022-08-18 12:26 |
|
|
Connexion by Barange » Sat, 2022-08-20 20:32 |
1 |
by jose carceller Sun, 2022-08-21 00:32 |
|
|
How to change vesc Hardware setting by Arman Karkotsyan » Sun, 2022-08-28 00:08 |
1 |
by frank Wed, 2022-08-31 10:29 |
|
|
Controller bricked after firmware update how to recover by ardillolambo » Sat, 2022-04-30 15:31 |
1 |
by skyline1970 Thu, 2022-11-24 21:35 |
|
|
Turn on VESC via CAN Message by castiaum » Thu, 2022-06-02 12:17 |
1 |
by frank Thu, 2022-06-02 15:14 |
|
|
Wand firmware 1.3 by peacue » Mon, 2021-11-22 09:59 |
1 |
by frank Mon, 2021-11-22 12:56 |
|
|
VESC 6.0 Hardware Shows Up As HW 410 in VESC-Tool by FWachter » Thu, 2017-12-21 20:51 |
1 |
by wdaehn Fri, 2017-12-22 08:22 |
|
|
BLDC switching frequency by tuloski » Wed, 2018-09-19 13:18 |
1 |
by bauck Tue, 2020-11-17 17:08 |
|
|
Will voltage offset on phase cause tracking to get wrong position? by TechAUmNu » Wed, 2018-01-17 18:14 |
1 |
by TechAUmNu Wed, 2018-01-17 21:42 |
|
|
Hall sensor detection failed (AWD setup) by frameto » Tue, 2018-10-02 22:02 |
1 |
by ronmotor Tue, 2020-10-27 02:20 |
|
|
firmware too old! by ad_brad » Sun, 2018-10-14 18:33 |
1 |
by arvidb Sun, 2018-10-14 19:21 |
|
|
VESC Control over NRF by Christian » Tue, 2018-03-27 14:42 |
1 |
by m.juan Wed, 2018-07-04 13:44 |
|
|
Limiting of throttle curves has no effect by Ackmaniac » Thu, 2017-09-07 17:21 |
1 |
by frank Tue, 2017-09-19 09:35 |
|
|
Firmware 3.29 hardware 4.12 , 0.5mOhm shunts by brushlessdevil » Sun, 2017-10-15 19:28 |
1 |
by benjamin Thu, 2017-10-19 15:15 |
|
|
[Contributing][FOC] injected ADC and code clarity by Guillaume227 » Fri, 2017-12-15 18:00 |
1 |
by Roger Wolff Sat, 2017-12-16 13:21 |
|
|
VESC 75300 .bin firmware file by Markula » Tue, 2021-08-17 09:09 |
1 |
by frank Tue, 2021-08-17 09:53 |
|
|
Why such an old ChibiOS? by jackherer » Fri, 2021-04-16 17:03 |
1 |
by TechAUmNu Sat, 2021-04-17 00:51 |
|
|
How to add offset Current on 4.10 FW by hideo040401 » Mon, 2021-04-19 19:22 |
1 |
by microcai Fri, 2021-08-13 12:57 |
|
|
Vesc Tool Does not include FW for your HW by Hooman » Sat, 2020-12-05 20:30 |
1 |
by skyline1970 Sat, 2021-02-13 10:53 |
|
|
change firmware hardware ESC by jessbello » Thu, 2020-12-24 16:56 |
1 |
by skyline1970 Sat, 2021-02-13 10:50 |
Log in to post new content in the forum.
