You are here
VESC Firmware
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Thread safety issues when using both serial and USB communication together by vadimz » Sun, 2018-12-23 16:32 |
0 |
by vadimz Sun, 2018-12-23 16:32 |
|
|
Apply current limits,1804 line mcpwm_foc.c by aishangmu » Wed, 2019-01-09 09:47 |
0 |
by aishangmu Wed, 2019-01-09 09:47 |
|
|
Help setting up dual vesc via CANBUS by Jaystro16 » Sun, 2019-08-04 01:39 |
0 |
by Jaystro16 Sun, 2019-08-04 01:39 |
|
|
Problem report: VESC keeps running at full reverse throttle after PPM input returns to mid-stick by chunkulator » Sun, 2019-08-11 00:34 |
0 |
by chunkulator Sun, 2019-08-11 00:34 |
|
|
Latest VESC FW completely broken on 4.12 hardware by chris1seto » Fri, 2019-04-05 17:41 |
0 |
by chris1seto Fri, 2019-04-05 17:54 |
|
|
I need a minor change to my firmware by cdw3423vesc » Sat, 2018-11-17 00:55 |
0 |
by cdw3423vesc Sat, 2018-11-17 00:55 |
|
|
Dual Vesc reading second wheel RPM by rdavenport3 » Tue, 2022-05-03 15:32 |
0 |
by rdavenport3 Tue, 2022-05-03 15:32 |
|
|
Request for Example: Can communication with Libcanard by WoofyBunny » Fri, 2022-05-13 03:44 |
0 |
by WoofyBunny Fri, 2022-05-13 03:45 |
|
|
Current sign varies between motors by vadimz » Fri, 2022-08-26 11:24 |
0 |
by vadimz Fri, 2022-08-26 11:24 |
|
|
The engine stopped spinning after updating firmware This topic has been moved to "VESC Tool" (View topic) |
|||
|
75300 r2 v5.3 by Oscarmanassan » Tue, 2022-09-27 14:23 |
0 |
by Oscarmanassan Tue, 2022-09-27 14:23 |
|
|
VESC firmware to programmable Sabvoton ml60 controller. by Maciejwarloch » Tue, 2022-03-08 13:25 |
0 |
by Maciejwarloch Tue, 2022-03-08 13:25 |
|
|
Sending Negative Values to VESC over CAN bus by olivierabristol » Fri, 2022-03-25 09:11 |
0 |
by olivierabristol Fri, 2022-03-25 09:13 |
|
|
Problem after flash fw 3.38 detection faild dont spin by kataklysm_9090 » Tue, 2018-06-19 22:48 |
0 |
by kataklysm_9090 Tue, 2018-06-19 22:48 |
|
|
Help with Focbox firmware / bootloader upgrade [VESC TOOL] by Enigmacpl03 » Thu, 2017-10-05 17:21 |
0 |
by Enigmacpl03 Thu, 2017-10-05 17:21 |
|
|
Vesc Tool cannot detect firmware by MARK EVERITT » Sat, 2018-06-30 18:36 |
0 |
by MARK EVERITT Sat, 2018-06-30 18:36 |
|
|
Move FAULT pin to GPIOD_PIN2 by CTSchorsch » Tue, 2018-09-04 10:13 |
0 |
by CTSchorsch Tue, 2018-09-04 10:13 |
|
|
VESC hardware interrupt pins by gpzhao » Sun, 2018-04-01 10:47 |
0 |
by gpzhao Sun, 2018-04-01 10:50 |
|
|
Cannot upgrade firmware by greensightag.com » Fri, 2018-04-27 02:32 |
0 |
by greensightag.com Fri, 2018-04-27 02:34 |
|
|
PWM length not correctly measured by ufechner » Tue, 2018-06-05 11:45 |
0 |
by ufechner Tue, 2018-06-05 11:45 |
|
|
PID Speed Control code....for NRF by Dimitri » Tue, 2017-10-03 07:16 |
0 |
by Dimitri Tue, 2017-10-03 07:18 |
|
|
Dutycycle set using uart problem by Raja Sharma » Tue, 2020-07-21 21:38 |
0 |
by Raja Sharma Tue, 2020-07-21 21:38 |
|
|
firmware w/ no hw limits by dewcantoo » Sat, 2025-07-19 21:10 |
0 |
by dewcantoo Sat, 2025-07-19 21:10 |
|
|
VESC 6 MKIII - Writing Custom Applications using Ubuntu by TanmayP » Wed, 2020-08-05 00:48 |
0 |
by TanmayP Wed, 2020-08-05 00:48 |
|
|
noob question - how to I update FW to 3.66? by brently » Thu, 2020-01-16 02:22 |
0 |
by brently Thu, 2020-01-16 02:22 |
|
Log in to post new content in the forum.
