You are here
VESC Firmware
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Which firmware do I need by Luka-Zagar » Tue, 2021-10-19 22:24 |
2 |
by Luka-Zagar Wed, 2021-10-20 19:38 |
|
|
Urgent VESC Firmware Issue by D1200 » Tue, 2021-11-16 02:32 |
2 |
by frank Tue, 2021-11-16 09:50 |
|
|
ESC FS75100 by myck33 » Fri, 2021-12-31 14:17 |
2 |
by jaykup Sun, 2022-01-16 22:43 |
|
|
Cannot downgrade from beta firmware by CasperK » Tue, 2022-08-16 16:56 |
2 |
by joeker24 Mon, 2022-09-05 14:09 |
|
|
mcpwm_set_current VS mcpwm_set_brake_current by stiganielsen » Wed, 2019-09-11 15:40 |
2 |
by mechhead Mon, 2022-02-14 11:04 |
|
|
200kHz PWM by c10yas » Sun, 2019-09-22 17:06 |
2 |
by Eric Thu, 2019-11-07 18:09 |
|
|
VESC Firmware (conf_general.h) by HopeAndWonder » Sat, 2020-05-16 20:44 |
2 |
by judylee Thu, 2020-06-18 11:25 |
|
|
Duty cycle take 95% when motor released by Rarikao » Mon, 2019-12-23 08:57 |
2 |
by agnesnorris Sat, 2020-02-29 03:48 |
|
|
Uploading compiled firmware results in no USB access by Count1310 » Sat, 2020-08-08 14:45 |
2 |
by ibarretos Sun, 2020-08-30 13:34 |
|
|
Driving Synchronous reluctance motor using VESC by mmandar90 » Fri, 2023-04-21 14:34 |
2 |
by Ganzey Thu, 2023-04-27 00:17 |
|
|
VESC FOC in Encoder Mode Unstable at High eRPM by bayetan » Sun, 2023-10-08 22:40 |
2 |
by bayetan Mon, 2023-10-09 16:20 |
|
|
Priority of CAN messages? by hmijail » Sat, 2018-10-27 06:30 |
2 |
by hmijail Fri, 2018-11-23 01:44 |
|
|
Firmware 3.37 too old, unable to Connect VESC_Tool by Nico Isn » Wed, 2018-04-18 11:17 |
2 |
by Nico Isn Fri, 2018-04-20 16:31 |
|
|
Uploaded Firmware, Not Updated by kneave » Sat, 2018-08-18 21:02 |
2 |
by kneave Sat, 2018-08-18 21:48 |
|
|
FEATURE REQUEST - ADC Mapping selection by Pimousse » Thu, 2018-09-13 09:44 |
2 |
by hackish Sun, 2019-12-08 03:53 |
|
|
VESC6 runs at 100% throttle, but then current sense is broken by nickw1881 » Mon, 2018-09-24 06:41 |
2 |
by moto_guy Thu, 2019-03-28 06:40 |
|
|
Twisted pair for Can Bus link cable? by Kenny-san650 » Tue, 2018-02-13 08:35 |
2 |
by Kenny-san650 Mon, 2018-02-19 09:15 |
|
|
VESC 100-250 doesn't work with firmware built from 100_250 folder by aerostepa » Sat, 2021-01-30 17:14 |
2 |
by aerostepa Sun, 2021-01-31 17:42 |
|
|
LM61 temperature sensor by ka_ru » Tue, 2020-10-13 11:55 |
2 |
by ka_ru Wed, 2020-10-14 17:33 |
|
|
Unbricking a bricked VESC6 - A step by step procedure by espen.oland » Tue, 2020-11-17 18:00 |
2 |
by h1989 Wed, 2024-11-06 06:42 |
|
|
FW stability by NATUITION » Fri, 2021-06-04 15:35 |
2 |
by berryarreo Wed, 2021-06-30 09:15 |
|
|
VESC 75300 R2 R3 , latest FW ? by E-Toxx » Sat, 2020-12-12 19:36 |
2 |
by shelbyflint Mon, 2021-04-05 09:49 |
|
|
Control System of VESC by mm_iem » Wed, 2021-08-25 14:52 |
2 |
by kubark42 Wed, 2021-11-17 16:59 |
|
|
Navigating the firmware by thewho » Fri, 2018-12-14 09:31 |
2 |
by TechAUmNu Fri, 2018-12-14 22:22 |
|
|
highspeed motors max erpm? by themotorman » Sun, 2018-12-30 00:50 |
2 |
by TechAUmNu Thu, 2019-01-03 17:25 |
Log in to post new content in the forum.
