You are here
VESC Firmware
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Sticky:
VESC 75/300 R2 with R1 Firmware by frank » Thu, 2019-11-28 09:39 |
1 |
by Henque19 Sat, 2021-04-24 22:48 |
|
|
Vesc Tool cannot detect firmware by MARK EVERITT » Sat, 2018-06-30 18:36 |
0 |
by MARK EVERITT Sat, 2018-06-30 18:36 |
|
|
Is there a way to deactivate roll to start function FW 5.02 by Philo » Fri, 2021-04-16 22:28 |
0 |
by Philo Sun, 2021-04-18 11:57 |
|
|
VESC not reporting ah charged or wh charged by trevorjones » Sun, 2021-05-02 06:59 |
0 |
by trevorjones Sun, 2021-05-02 06:59 |
|
|
Safety Signal by Flepple » Thu, 2020-11-26 12:17 |
0 |
by Flepple Mon, 2020-11-30 16:17 |
|
|
Move FAULT pin to GPIOD_PIN2 by CTSchorsch » Tue, 2018-09-04 10:13 |
0 |
by CTSchorsch Tue, 2018-09-04 10:13 |
|
|
Torque6 firmware trouble by Romanceismygift » Sun, 2021-05-09 22:07 |
0 |
by Romanceismygift Sun, 2021-05-09 22:07 |
|
|
Switchign frequency issue? by Maxid » Thu, 2020-12-03 11:47 |
0 |
by Maxid Thu, 2020-12-03 11:47 |
|
|
Regenerative Braking by silvatma » Wed, 2021-05-26 00:38 |
0 |
by silvatma Wed, 2021-05-26 00:38 |
|
|
Use Mutexes within the ppm app by talabo » Thu, 2021-07-15 12:25 |
0 |
by talabo Thu, 2021-07-15 12:25 |
|
|
75/300 R2 FW higher than 3.62 ? it is possible? by Lasse » Sat, 2020-12-26 20:34 |
0 |
by Lasse Sat, 2020-12-26 20:34 |
|
|
VESC hardware interrupt pins by gpzhao » Sun, 2018-04-01 10:47 |
0 |
by gpzhao Sun, 2018-04-01 10:50 |
|
|
Regarding code documentation by hiddenzed » Mon, 2021-02-08 12:40 |
0 |
by hiddenzed Mon, 2021-02-08 12:40 |
|
|
Change some VESC configurations by nltb » Fri, 2020-09-11 13:39 |
0 |
by nltb Fri, 2020-09-11 13:39 |
|
|
Cannot upgrade firmware by greensightag.com » Fri, 2018-04-27 02:32 |
0 |
by greensightag.com Fri, 2018-04-27 02:34 |
|
|
FLIPSKY FSESC V4 50A SK8-ESC w / 5V / 1.5A BEC Fast start¡¡¡ by Oscar Lozano Gimenez » Sun, 2021-02-21 23:26 |
0 |
by Oscar Lozano Gimenez Sun, 2021-02-21 23:26 |
|
|
vesc tool v1.05 fw 3.51 by at_dts » Wed, 2020-09-23 20:12 |
0 |
by at_dts Wed, 2020-09-23 20:12 |
|
|
PWM length not correctly measured by ufechner » Tue, 2018-06-05 11:45 |
0 |
by ufechner Tue, 2018-06-05 11:45 |
|
|
PID Speed Control code....for NRF by Dimitri » Tue, 2017-10-03 07:16 |
0 |
by Dimitri Tue, 2017-10-03 07:18 |
|
|
Problem after flash fw 3.38 detection faild dont spin by kataklysm_9090 » Tue, 2018-06-19 22:48 |
0 |
by kataklysm_9090 Tue, 2018-06-19 22:48 |
|
|
Help with Focbox firmware / bootloader upgrade [VESC TOOL] by Enigmacpl03 » Thu, 2017-10-05 17:21 |
0 |
by Enigmacpl03 Thu, 2017-10-05 17:21 |
|
|
Need help understanding how VESC firmware works by khojka » Sun, 2021-04-11 16:55 |
0 |
by khojka Sun, 2021-04-11 16:55 |
|
|
Modifications Needed for Custom Dual Motor ESC for 3S Operation by NK-108 » Mon, 2025-12-15 18:27 |
0 |
by NK-108 Mon, 2025-12-15 18:27 |
|
|
Low-Speed Hall Interpolation Performance Issues by cpaterson » Tue, 2026-01-27 03:42 |
0 |
by cpaterson Tue, 2026-01-27 03:42 |
|
|
Compiled Firmware in limited mode by sirAnton » Sat, 2026-03-21 10:13 |
0 |
by sirAnton Sat, 2026-03-21 10:13 |
Log in to post new content in the forum.
