You are here
VESC Tool
Log in to post new content in the forum.
Topic / Topic starter | Replies | Last post | |
---|---|---|---|
Hoverboard motor Reverse direction by Silvio Semedo » Sat, 2021-01-16 17:43 |
1 |
by skyline1970 Sun, 2021-02-07 17:32 |
|
Erpm / torque setting with remote control, Vesc wand by Lasse » Fri, 2021-02-05 22:41 |
1 |
by skyline1970 Tue, 2021-02-09 20:03 |
|
Custom plots in VESC - Tool by kinzma » Sun, 2019-07-28 11:44 |
5 |
by jfaille Wed, 2021-02-10 07:50 |
|
VESC-Standard from enertionboards hardware version by soccerbeast003 » Wed, 2021-01-20 18:48 |
1 |
by skyline1970 Sat, 2021-02-13 10:17 |
|
Low RPM motor stutter? by ebikerevolution » Mon, 2019-01-21 20:06 |
8 |
by Tibor Kalman Za... Sat, 2021-02-13 13:59 |
|
VESCTOOL - Multiple VESC simultaneous configuration (Same CANBUS ID issues) by Filcas » Thu, 2021-02-18 20:52 |
2 |
by Filcas Fri, 2021-02-19 01:37 |
|
Benchmark regenerative braking by diggis » Fri, 2021-02-19 10:01 |
0 |
by diggis Fri, 2021-02-19 10:01 |
|
How do I disable brake? by moo10032 » Tue, 2021-02-23 08:09 |
0 |
by moo10032 Tue, 2021-02-23 08:10 |
|
How to increase startup torque? by Enak » Fri, 2017-09-08 01:14 |
4 |
by vadicus Tue, 2021-02-23 19:44 |
|
Custom GUI by FatsoBatso » Thu, 2021-02-25 16:10 |
0 |
by FatsoBatso Thu, 2021-02-25 16:10 |
|
Firmware 5.2 how to Fast start¡¡¡ by Oscar Lozano Gimenez » Tue, 2021-02-23 10:00 |
1 |
by skyline1970 Fri, 2021-02-26 15:09 |
|
RPM increase by Tibor Kalman Za... » Tue, 2021-02-23 10:12 |
2 |
by Tibor Kalman Za... Sat, 2021-02-27 21:41 |
|
MAX ERPM by riderman » Sun, 2021-02-28 23:05 |
0 |
by riderman Sun, 2021-02-28 23:05 |
|
How to set max input voltage to over 57 volts? by johnny5in5 » Thu, 2020-09-24 03:34 |
3 |
by TheFallen Mon, 2021-03-01 16:42 |
|
Been at it for like 14 hours... HALP by mnchvgs79 » Wed, 2021-03-03 22:03 |
4 |
by TheFallen Sun, 2021-03-07 15:25 |
|
FSESC 6.6 200A Unable to send signal to slave VESC by bms368 » Sat, 2021-02-20 06:16 |
1 |
by adidasgoogle Sun, 2021-03-07 19:11 |
|
Throttle and Brake by shatty » Wed, 2021-03-10 01:19 |
0 |
by shatty Wed, 2021-03-10 01:22 |
|
I Mac Vesc tool !!!! by PHATTY » Fri, 2019-10-11 17:56 |
2 |
by Bender Wed, 2021-03-10 14:39 |
|
Update fail from FW3.58 to 3.61 by sachs2019 » Tue, 2019-09-10 15:51 |
7 |
by AlmaRaposa Thu, 2021-03-11 17:44 |
|
Battery Voltage Settings by huffauden19 » Wed, 2020-03-04 23:17 |
2 |
by laser30 Sat, 2021-03-13 16:57 |
|
motor stops spinning on its own by rsarver » Tue, 2021-03-16 16:30 |
1 |
by rsarver Tue, 2021-03-16 22:13 |
|
D vs omega control by rsarver » Wed, 2021-03-17 14:44 |
0 |
by rsarver Wed, 2021-03-17 14:44 |
|
Data logging by charper » Wed, 2019-05-22 00:48 |
4 |
by StvMan Sun, 2021-03-21 17:20 |
|
Full Brake vs Switch Off by meisterpro » Mon, 2021-03-22 14:36 |
0 |
by meisterpro Mon, 2021-03-22 14:36 |
|
VESC failure presumably due to current oscillations at high current by rsarver » Wed, 2021-03-24 22:06 |
0 |
by rsarver Wed, 2021-03-24 22:06 |
Log in to post new content in the forum.