You are here
VESC Tool
Log in to post new content in the forum.
Topic / Topic starter | Replies | Last post | |
---|---|---|---|
Flipsky nrf51288 by Idoff » Tue, 2018-12-11 21:33 |
2 |
by frank Mon, 2019-02-18 09:00 |
|
Is there a complete documentation for the communication protocol between the vesc tool and the board? by aishangmu » Tue, 2018-12-25 09:00 |
2 |
by Caustic_Zinc Fri, 2019-02-08 19:27 |
|
Autodetection algorithm by Griffen » Thu, 2019-01-03 18:44 |
2 |
by Gmack Fri, 2020-09-18 16:39 |
|
cant connect via usb by curtm » Wed, 2019-06-19 03:05 |
2 |
by curtm Thu, 2019-07-04 00:37 |
|
Fault Codes by Joe_Lowtech » Wed, 2019-02-13 20:06 |
2 |
by mthielvoldt Thu, 2019-07-18 00:38 |
|
Advanced settings for FOC motor detection (flux linkage) by jaghori.sasan » Sun, 2019-02-17 09:34 |
2 |
by jaghori.sasan Sun, 2019-02-17 17:51 |
|
Understanding FOC Wizard Innerworkings by gravity99 » Thu, 2022-08-18 22:24 |
2 |
by gravity99 Mon, 2022-08-22 15:23 |
|
Detection failed. Reason: Flux linkage detection failed by Donnyten » Sun, 2022-10-09 20:31 |
2 |
by Donnyten Tue, 2022-10-11 02:56 |
|
Vesc Tool For Mac by kmfpod » Tue, 2022-06-14 22:06 |
1 |
by frank Wed, 2022-06-15 09:58 |
|
Pictures from "Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller"? by timmertens » Thu, 2022-06-16 17:56 |
1 |
by frank Thu, 2022-06-16 19:47 |
|
Taking 5-6 seconds for running motor under ADC mode by asnamp » Fri, 2022-06-24 13:02 |
1 |
by skyline1970 Thu, 2022-11-24 21:24 |
|
Cannot connect to vesc tool app by sharpshooterjd » Fri, 2022-07-29 23:39 |
1 |
by skyline1970 Sun, 2022-11-27 16:38 |
|
Motor Stuck at 55% Duty Cycle by motion_sickness » Sun, 2021-11-14 16:47 |
1 |
by drdrs Sun, 2021-11-14 21:20 |
|
Use sensors on the output shaft of a motor attached to a large gear ratio gearbox by davidq1688 » Wed, 2022-04-27 05:23 |
1 |
by tobiokanobi Thu, 2022-04-28 14:48 |
|
Vesc doesn't react to can messages from PC by BorisDeroo » Fri, 2021-12-17 16:54 |
1 |
by yuri12 Wed, 2022-02-09 17:33 |
|
inconsistent behavior after motor control using FOC by alexantosh » Wed, 2022-01-05 10:24 |
1 |
by frank Wed, 2022-01-05 11:21 |
|
NRF5X SWD Prog detection broken, always detects NRF52832 512K/64K by zippy » Sun, 2021-06-06 16:19 |
1 |
by zippy Sun, 2021-06-06 17:58 |
|
ERPM scaling / Maximum motor speed / RPM by Azza » Tue, 2019-09-03 17:16 |
1 |
by Azza Fri, 2019-09-06 18:20 |
|
VESC 4.12 - Current limited at 100A by Laerson » Sun, 2019-09-08 20:23 |
1 |
by benjamin Mon, 2019-09-09 18:20 |
|
Phase Correct PWM Setting? by orangepig111 » Tue, 2021-07-20 07:39 |
1 |
by skyline1970 Fri, 2021-10-29 12:52 |
|
VESC tool 0.94 needed(Linux) by tahirhasan » Wed, 2019-09-11 16:34 |
1 |
by mustafa Sun, 2019-11-10 20:34 |
|
Is there a download link for VESC 2.06 for Mac OS? by Harrison Edwards » Sun, 2021-08-22 05:59 |
1 |
by frank Sun, 2021-08-22 11:52 |
|
ConfBackup, Where does it save it by mikemoy » Tue, 2021-09-07 16:25 |
1 |
by ndp Thu, 2022-05-12 20:25 |
|
Compiled Vesc Tool Won't Recognize Firmware - Windows 1.23 by KingRagnar22 » Wed, 2019-10-02 01:29 |
1 |
by a.dahhak Mon, 2021-02-01 16:54 |
|
Can´t increase current by increase RPM by hubacek000 » Mon, 2021-09-13 13:22 |
1 |
by frank Tue, 2021-09-14 12:17 |
Log in to post new content in the forum.