You are here
VESC Tool
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
How to edit mobile RT gauges? by colmor » Sun, 2025-02-02 05:20 |
0 |
by colmor Sun, 2025-02-02 05:20 |
|
|
LSM6DS3 gyro ? for balancing by amaussa » Sun, 2020-09-13 12:51 |
1 |
by amaussa Mon, 2020-09-21 17:21 |
|
|
VESC tool Data log / CSV by Ole Skov » Mon, 2020-05-25 19:47 |
1 |
by mpater Sat, 2021-12-25 11:25 |
|
|
Write App Configuration via UART [SOLVED] by v8-rt » Mon, 2020-11-02 13:13 |
1 |
by Halas1941 Sun, 2020-11-29 14:04 |
|
|
Max RPM by donrecardo » Thu, 2020-06-25 12:00 |
1 |
by Tibor Kalman Za... Mon, 2020-06-29 21:03 |
|
|
Is Vesc Tool App Hogging the Bluetooth? by Marctwo » Mon, 2020-07-06 11:10 |
1 |
by Marctwo Thu, 2020-07-09 08:29 |
|
|
Install VESC on ubuntu 18.04 bionic not working by rest_vesc_001 » Fri, 2020-12-11 18:25 |
1 |
by RitaGilmore Fri, 2021-01-22 16:36 |
|
|
VESC Tool Battery Settings for 5S Lipo by Bildoon » Sat, 2020-04-04 23:28 |
1 |
by Bildoon Mon, 2020-04-06 01:24 |
|
|
Ac synchronous motor support by Yksbs » Mon, 2020-08-24 07:14 |
1 |
by skyline1970 Sat, 2020-11-21 11:11 |
|
|
KV command in terminal ( how to determine kv of a motor ) by fessyfoo » Sat, 2020-05-09 21:21 |
1 |
by rafeh1 Mon, 2022-08-08 04:31 |
|
|
Partial throttle input smoothing / jerky control by moose09876 » Thu, 2023-08-10 20:56 |
1 |
by moose09876 Sun, 2023-09-24 19:28 |
|
|
Flipsky 75100foc motor detection sensor issue fails every crysaltemotor I've tried by Wheelzscootersinc » Fri, 2023-02-03 21:36 |
1 |
by tom355 Sun, 2023-02-05 11:11 |
|
|
Looking for 3.01 apk by jsbenson » Sun, 2023-09-10 01:49 |
1 |
by jsbenson Sun, 2023-09-10 04:11 |
|
|
RPM not Working? by ngilchr » Fri, 2023-10-06 16:39 |
1 |
by bayetan Sun, 2023-10-08 23:03 |
|
|
VESC Tool crashes when loading/saving motor/app config by bkyrevolution » Thu, 2023-03-02 20:27 |
1 |
by jimtzer Mon, 2023-03-13 00:30 |
|
|
Expert VESC programmer wanted by SGi » Mon, 2023-10-23 01:59 |
1 |
by electricfox Mon, 2023-10-23 09:12 |
|
|
Acceleration ramping using UART communication with arduino on VTool 6.0 by Kokonenen » Tue, 2023-04-04 11:48 |
1 |
by Kokonenen Tue, 2023-04-04 14:30 |
|
|
Motor always accelerates to maximum speed by zapshe » Sun, 2022-09-11 03:46 |
1 |
by skyline1970 Sun, 2022-11-27 16:32 |
|
|
Another Motor Detection Thread by MaksK » Wed, 2019-01-02 21:05 |
1 |
by TechAUmNu Thu, 2019-01-03 17:23 |
|
|
Sensored FOC not working by Jarson » Thu, 2019-01-24 20:03 |
1 |
by Caustic_Zinc Fri, 2019-02-08 19:19 |
|
|
Parametre for Low RPM Limit by ilan248@gmail.com » Wed, 2019-07-10 11:01 |
1 |
by askker Thu, 2019-07-11 05:04 |
|
|
Changing Output Voltage frequency by davbams » Wed, 2019-07-24 21:20 |
1 |
by district9prawn Thu, 2019-07-25 02:59 |
|
|
Help setting up dual vesc via CANBUS by Jaystro16 » Sun, 2019-08-04 01:39 |
1 |
by frank Wed, 2019-08-14 13:55 |
|
|
vesc tool crashing on 29aug19 - website down/link? by ianp » Fri, 2019-08-30 04:10 |
1 |
by frank Mon, 2019-09-02 11:26 |
|
|
How to determine motor size in wizard, hub motors ? by Photolad61 » Mon, 2019-03-25 19:43 |
1 |
by Kent Tabor Fri, 2020-10-23 22:29 |
Log in to post new content in the forum.
