You are here
VESC Tool
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Wolf king 11 gt 72v 35ah perimeter setting help by jsherbz92 » Tue, 2025-04-01 08:37 |
0 |
by jsherbz92 Tue, 2025-04-01 08:37 |
|
|
Connecting over USB with M1 Macs by hyperdash » Tue, 2025-04-08 02:25 |
0 |
by hyperdash Tue, 2025-04-08 02:25 |
|
|
eBike Speed (mph or kph) with mechanical transmission by Rit » Tue, 2026-04-28 02:11 |
0 |
by Rit Mon, 2026-06-01 22:10 |
|
|
UART Servo Output Works in VESC‑Tool UI but Not via ROS Publish by Shreeram2311 » Tue, 2025-05-06 02:40 |
0 |
by Shreeram2311 Tue, 2025-05-06 02:40 |
|
|
Calculate Power from RT Data by Rit » Mon, 2026-06-01 23:46 |
0 |
by Rit Mon, 2026-06-01 23:46 |
|
|
Reverse gear is engaged when power is lost by simDen » Mon, 2024-09-30 13:18 |
0 |
by simDen Mon, 2024-09-30 13:18 |
|
|
Rough Stutter when taking off (48V 750w 75100 Pro v2) by ahagie » Mon, 2024-11-04 01:21 |
0 |
by ahagie Mon, 2024-11-04 01:21 |
|
|
VESC Tool Device UI not shown on Raspberry Pi/Linux by Sebastiaan Koning » Mon, 2024-12-02 13:19 |
0 |
by Sebastiaan Koning Mon, 2024-12-02 13:19 |
|
|
Vesc tool app not installed on Samsung a02s by Zuky » Sun, 2025-08-03 20:31 |
0 |
by Zuky Sun, 2025-08-03 20:32 |
|
|
Flipsky FSESC 6.7PRO and bluetooth module by phonkie » Mon, 2025-08-18 06:33 |
0 |
by phonkie Mon, 2025-08-18 06:33 |
|
|
lispBM command "gpio-hold" by Jamesavery22 » Sat, 2025-01-04 20:46 |
0 |
by Jamesavery22 Sat, 2025-01-04 20:46 |
|
|
Battery profiles? by ahagge » Mon, 2025-09-01 16:36 |
0 |
by ahagge Mon, 2025-09-01 16:36 |
|
|
Odys Alpha X3 Pro Settings by flashice » Mon, 2025-01-06 14:28 |
0 |
by flashice Mon, 2025-01-06 14:34 |
|
|
turn counter by player107 » Wed, 2025-09-10 22:52 |
0 |
by player107 Wed, 2025-09-10 22:52 |
|
|
Urgent Help Connecting TS5700N8501-like Magnetic Encoder by jumana » Tue, 2025-01-14 19:37 |
0 |
by jumana Tue, 2025-01-14 19:37 |
|
|
limited mode by Satrio » Fri, 2025-09-26 16:31 |
0 |
by Satrio Fri, 2025-09-26 16:31 |
|
|
Vesc Tool 6.06 test version 2 error by NOAI » Sat, 2025-01-25 13:00 |
0 |
by NOAI Sat, 2025-01-25 13:00 |
|
|
PID Speed Control Type by User18 » Fri, 2025-10-31 19:35 |
0 |
by User18 Fri, 2025-10-31 19:35 |
|
|
Very low Flux Linkage calulation FOC,General Tab - 0.0xx mWb by kjjajsdASHD » Sun, 2025-02-02 13:59 |
0 |
by kjjajsdASHD Sun, 2025-02-02 13:59 |
|
|
VESC Tool IMU Problem by 13.meshhi » Sun, 2025-11-16 23:40 |
0 |
by 13.meshhi Sun, 2025-11-16 23:40 |
|
|
Input Setup Wizard - Update Firmware by pmg » Thu, 2020-02-13 09:54 |
0 |
by pmg Thu, 2020-02-13 09:54 |
|
|
ADC and arrow input dont work by stefann » Wed, 2019-10-09 18:51 |
0 |
by stefann Wed, 2019-10-09 20:04 |
|
|
Reconstruct detection control algorithm inside the tool by kaanozgen » Wed, 2020-02-26 18:50 |
0 |
by kaanozgen Wed, 2020-02-26 18:50 |
|
|
Current measurement VESC Tool 1.16 by mdbb » Thu, 2020-03-19 17:16 |
0 |
by mdbb Thu, 2020-03-19 17:16 |
|
|
DC MOTOR connected to FLIPSKY 4.20 MINI by CatalinCHIRICA » Mon, 2019-12-02 18:20 |
0 |
by CatalinCHIRICA Mon, 2019-12-02 18:20 |
Log in to post new content in the forum.
