You are here
VESC Tool
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
version of Vesc Tool for Flipsky 6.6 by Robert Adkins » Sun, 2019-09-29 18:13 |
3 |
by frank Wed, 2019-10-23 09:35 |
|
|
Vesc Tool For Mac by kmfpod » Tue, 2022-06-14 22:06 |
2 |
by nic sandiland Sun, 2025-09-21 18:21 |
|
|
pulsation at mid speed by smallbikefun » Sun, 2024-05-12 19:00 |
2 |
by Lizzle Wed, 2024-09-04 06:07 |
|
|
bidirectional joystick conrol with saparate brake switch by Erik fijlstra » Thu, 2024-05-16 16:02 |
2 |
by Erik fijlstra Mon, 2024-08-05 16:39 |
|
|
Writing to slave vesc sometimes cause loss of can bus by meashman » Wed, 2022-07-20 01:08 |
2 |
by frank Thu, 2022-10-27 08:54 |
|
|
Writing value to both VESCs on FocFox Unity by agraham » Wed, 2022-02-23 21:45 |
2 |
by benjamin Thu, 2022-02-24 10:57 |
|
|
Calibration ERROR with TLE5012B Magnetic encoder in ABI mode by cejota » Fri, 2022-03-25 03:19 |
2 |
by XieMaster Mon, 2022-11-14 05:32 |
|
|
VESC Tool 6.02 by JWilson » Thu, 2024-03-21 18:30 |
2 |
by LiamSa66 Mon, 2026-05-25 22:20 |
|
|
vesc UART with arduino 33 BLE by amaussa » Mon, 2020-10-12 16:57 |
2 |
by Seb44120 Fri, 2020-11-20 23:06 |
|
|
VESC not connecting by jetomit » Wed, 2020-05-20 16:08 |
2 |
by Kent Tabor Sat, 2020-10-17 15:48 |
|
|
VECT Tool freezes after uploading lisp script by realphanta » Sun, 2025-07-27 17:05 |
2 |
by realphanta Thu, 2025-07-31 11:24 |
|
|
IOS - VESCTOOL Run successfully ? by Bear Chris » Mon, 2025-01-06 08:54 |
2 |
by Bear Chris Mon, 2025-01-06 15:06 |
|
|
vesc tool not opening by RemyMade413 » Sat, 2026-02-28 12:15 |
2 |
by mariuszdymon Sat, 2026-02-28 23:07 |
|
|
Autodetection algorithm by Griffen » Thu, 2019-01-03 18:44 |
2 |
by Gmack Fri, 2020-09-18 16:39 |
|
|
cant connect via usb by curtm » Wed, 2019-06-19 03:05 |
2 |
by curtm Thu, 2019-07-04 00:37 |
|
|
Fault Codes by Joe_Lowtech » Wed, 2019-02-13 20:06 |
2 |
by mthielvoldt Thu, 2019-07-18 00:38 |
|
|
Advanced settings for FOC motor detection (flux linkage) by jaghori.sasan » Sun, 2019-02-17 09:34 |
2 |
by jaghori.sasan Sun, 2019-02-17 17:51 |
|
|
"bad detection result received" impossible to achieved motor detection ! by titimomotete » Wed, 2019-03-20 17:21 |
2 |
by doom Mon, 2019-08-05 10:52 |
|
|
VESC Tool 0.95 App by einbi » Tue, 2018-10-09 11:02 |
2 |
by Yanick Hautecoeur Thu, 2021-09-30 13:55 |
|
|
Flipsky nrf51288 by Idoff » Tue, 2018-12-11 21:33 |
2 |
by frank Mon, 2019-02-18 09:00 |
|
|
Is there a complete documentation for the communication protocol between the vesc tool and the board? by aishangmu » Tue, 2018-12-25 09:00 |
2 |
by Caustic_Zinc Fri, 2019-02-08 19:27 |
|
|
Vesctool otg by meashman » Sat, 2022-08-06 10:05 |
2 |
by meashman Wed, 2022-08-17 06:39 |
|
|
motor max rpm and current severely limited? by Roy Zhang » Mon, 2021-08-09 19:23 |
2 |
by vadicus Thu, 2021-08-12 04:06 |
|
|
Overheating protection, voltage-/current-limitation etc. by kianK » Thu, 2021-04-15 07:23 |
2 |
by lilliamhoyle Wed, 2021-07-07 09:36 |
|
|
VESC tool and sk8-esc V6 set up shows incorrectcurrent usage by DominykasS » Fri, 2022-09-30 13:54 |
2 |
by Frizzaper Wed, 2023-11-15 04:25 |
Log in to post new content in the forum.
