You are here

VESC Tool

Topic / Topic starter Replies Last postsort ascending
Normal topic Trouble downloading the tool
by maxhertz » Tue, 2022-01-25 03:12
6
by frank
Sat, 2022-02-05 11:02
Normal topic Setup motor foc
by Vincent LAMBERT » Thu, 2022-02-03 12:22
0
by Vincent LAMBERT
Thu, 2022-02-03 12:22
Normal topic NRF connection error
by Denn » Wed, 2022-02-02 11:17
0
by Denn
Wed, 2022-02-02 11:17
Normal topic current of holding
by reff » Thu, 2022-01-27 16:38
0
by reff
Thu, 2022-01-27 16:39
Normal topic The engine stopped spinning after updating firmware
by brian adilman » Wed, 2022-01-26 17:40
0
by brian adilman
Wed, 2022-01-26 19:15
Normal topic Motor clicking and not spinning after setup wizard
by dfelz » Fri, 2020-04-03 03:51
6
by brian adilman
Wed, 2022-01-26 13:36
Normal topic VESC Tool on Windows 10 32 Bit doesn't open
by Red_Speedster » Mon, 2021-05-31 16:33
2
by frank
Wed, 2022-01-26 08:21
Normal topic Minimum System Requirements for VESC Tool 3.01 under Windows
by j.konrad » Mon, 2022-01-24 21:48
0
by j.konrad
Mon, 2022-01-24 21:48
Normal topic Vesc Tool Mobile can't update Vesc Firmware
by Happy Giraffe » Wed, 2022-01-19 21:48
2
by Happy Giraffe
Thu, 2022-01-20 23:50
Normal topic Max OSX version
by emmaanuel » Tue, 2017-09-05 13:03
6
by briona112
Thu, 2022-01-20 05:27
Normal topic questions about "RUN DETECTION"
by yuri12 » Thu, 2022-01-20 04:30
0
by yuri12
Thu, 2022-01-20 04:30
Normal topic Serial port errors with VESC Tool 3.00 and Flipsky FSESC 7550
by mckenzie.keith » Thu, 2022-01-06 02:24
1
by mckenzie.keith
Thu, 2022-01-06 18:54
Normal topic inconsistent behavior after motor control using FOC
by alexantosh » Wed, 2022-01-05 10:24
1
by frank
Wed, 2022-01-05 11:21
Normal topic Detection failed. Reason: Sensor detection failed
by Lilian_CASTEL » Tue, 2020-11-24 11:31
6
by danielhugentobler
Sat, 2022-01-01 23:15
Hot topic FOC detection error " R is 0"
by MontPierre » Fri, 2017-09-08 19:52
38
by danielhugentobler
Sat, 2022-01-01 23:13
Normal topic VESC tool Data log / CSV
by Ole Skov » Mon, 2020-05-25 19:47
1
by mpater
Sat, 2021-12-25 11:25
Normal topic One trasmitter two receivers
by vikiki » Wed, 2021-11-17 20:40
4
by Johnvoss
Fri, 2021-12-24 03:57
Normal topic Custom Apps
by HammerHeadFett » Fri, 2020-07-17 00:10
9
by CTSchorsch
Wed, 2021-12-22 09:12
Normal topic terminal command via UART for a gimbal
by fredfred » Sat, 2021-12-18 20:49
0
by fredfred
Sat, 2021-12-18 20:49
Normal topic Current In vs Current Motor
by hacksmithCabe » Thu, 2021-09-30 21:59
5
by y-hasebe
Mon, 2021-12-13 15:17
Normal topic App. settings: "Enable servo output on PPM-port when PPM-app is disabled." option
by alexantosh » Fri, 2021-12-10 09:46
0
by alexantosh
Fri, 2021-12-10 09:46
Normal topic Vesc-tool TCP Connection
by nlabs » Fri, 2017-12-08 02:30
1
by milesf
Fri, 2021-12-10 03:40
Normal topic Motor control
by ptss37 » Wed, 2021-12-08 06:52
5
by ptss37
Fri, 2021-12-10 03:24
Normal topic Logging set values to csv file
by jukawt » Mon, 2021-12-06 14:57
0
by jukawt
Mon, 2021-12-06 14:57
Normal topic windows 7 VESC TOOL 1.25 wont open/not responding HELP PLEASE
by timgoebel12@gma... » Tue, 2019-11-12 00:42
3
by yehsk8rz
Sat, 2021-12-04 20:52
New posts
No new posts
Hot topic with new posts
Hot topic without new posts
Sticky topic
Locked topic
Subscribe to RSS - VESC Tool