You are here
VESC Tool
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
VESC Tool 0.87 by pieschie » Sun, 2018-08-26 12:38 |
3 |
by Roger Wolff Sun, 2018-09-16 12:00 |
|
|
Serial port error when Encoder detection is complete by VirtB » Wed, 2018-08-29 03:03 |
3 |
by VirtB Sun, 2018-09-02 03:33 |
|
|
Vesc-Tool Raspbian compatible build by mjc60 » Fri, 2017-09-08 18:20 |
3 |
by RSR Tue, 2017-09-19 11:35 |
|
|
FOC detection.... by Roger Wolff » Thu, 2018-05-24 17:37 |
3 |
by TechAUmNu Sun, 2018-05-27 21:14 |
|
|
Duty Cycle Acceleration Limit by jfaille » Tue, 2020-06-16 23:17 |
3 |
by amaussa Sun, 2020-09-13 12:59 |
|
|
vesc for helicopter tail rotor / freewheel for duty cycle mode by vladimir757 » Thu, 2020-06-25 14:25 |
3 |
by skyline1970 Thu, 2021-02-04 21:38 |
|
|
benjamin, New feature please by justinlinh » Sat, 2020-07-11 00:06 |
3 |
by justinlinh Sat, 2020-07-11 01:42 |
|
|
Custom Battery Settings? Inaccurate Wh readings? by dfelz » Wed, 2020-04-08 02:04 |
3 |
by starset Wed, 2021-01-13 22:54 |
|
|
Serial Control From PC by aguzel » Fri, 2020-08-21 02:45 |
3 |
by Jens Mon, 2022-11-28 20:40 |
|
|
How to select in VESC Tool the COM port of PC for USB connection to VESC6? by Heimfried » Mon, 2020-05-11 20:27 |
3 |
by Heimfried Wed, 2020-06-10 11:54 |
|
|
How to set max input voltage to over 57 volts? by johnny5in5 » Thu, 2020-09-24 03:34 |
3 |
by TheFallen Mon, 2021-03-01 16:42 |
|
|
Can't spin both motors over CAN-bus by Kokonenen » Wed, 2023-04-19 11:19 |
3 |
by Kokonenen Fri, 2023-04-21 09:18 |
|
|
How Can I make the tool work with FW 3.5 instead of just 3.58? by ipbyrne » Fri, 2019-07-26 18:20 |
3 |
by frank Wed, 2019-08-14 14:01 |
|
|
Setup parameters for battery in VESC Tool by Ulrich » Tue, 2019-02-26 11:47 |
3 |
by Photolad61 Wed, 2019-03-27 17:26 |
|
|
How to control motor using VESC tool in computer at constant rpm? by vimi94 » Wed, 2019-05-01 12:56 |
3 |
by foreclosurecat Tue, 2022-12-06 22:36 |
|
|
If firmware aint broke, dont fix it. by nickw1881 » Thu, 2019-10-31 07:32 |
3 |
by frank Wed, 2019-11-06 12:39 |
|
|
windows 7 VESC TOOL 1.25 wont open/not responding HELP PLEASE by timgoebel12@gma... » Tue, 2019-11-12 00:42 |
3 |
by yehsk8rz Sat, 2021-12-04 20:52 |
|
|
supported firmware by velolac » Mon, 2020-01-13 22:55 |
3 |
by velolac Tue, 2020-01-14 21:47 |
|
|
Question about COMM_GET_IMU_DATA packet by rrzaripov » Wed, 2020-03-04 00:28 |
3 |
by Addy Fri, 2020-04-24 06:49 |
|
|
No brakes in PID Speed Control mode by karololo » Tue, 2019-10-15 11:31 |
3 |
by Gesndrery Thu, 2019-12-26 07:00 |
|
|
motor experiment does nothing by greaterebiz » Mon, 2022-04-11 18:27 |
3 |
by swinckler Fri, 2022-07-01 14:38 |
|
|
Vesc can't connect to vesc tool by Roansky1 » Sat, 2022-04-30 13:05 |
3 |
by frank Tue, 2022-05-03 20:52 |
|
|
Motor temperature, how to set limit >120 C ? by RSR » Wed, 2018-08-22 12:40 |
3 |
by Danny Bokma Thu, 2018-08-23 07:19 |
|
|
Please explain the parameters in VESC-Tool by Knight » Wed, 2018-09-05 11:45 |
3 |
by Pimousse Tue, 2018-10-30 19:21 |
|
|
Help needed for VESC set up! by mbagrey » Wed, 2018-09-19 22:07 |
3 |
by Roger Wolff Sun, 2018-09-30 16:15 |
Log in to post new content in the forum.
