You are here
VESC Tool
Log in to post new content in the forum.
Topic / Topic starter |
Replies | Last post | |
|---|---|---|---|
|
TWO MOTOR SYSTEM by ronmotor » Mon, 2022-10-17 00:44 |
0 |
by ronmotor Mon, 2022-10-17 00:44 |
|
|
two motors one ppm for throttle and one for the direction? by Robby Ertmann » Wed, 2021-04-21 13:48 |
0 |
by Robby Ertmann Wed, 2021-04-21 13:48 |
|
|
UART Safety Feature by jaghori.sasan » Wed, 2019-09-04 18:45 |
0 |
by jaghori.sasan Wed, 2019-09-04 18:45 |
|
|
UART Servo Output Works in VESC‑Tool UI but Not via ROS Publish by Shreeram2311 » Tue, 2025-05-06 02:40 |
0 |
by Shreeram2311 Tue, 2025-05-06 02:40 |
|
|
UART write read arduino by matiller » Sat, 2019-06-01 20:18 |
0 |
by matiller Sat, 2019-06-01 20:18 |
|
|
Unable to connect to vesc through can bus by Kupofty » Thu, 2022-10-20 16:24 |
0 |
by Kupofty Thu, 2022-10-20 16:24 |
|
|
Unable to Make Changes in VESC Tool – field weakening Options Missing by asaf1462 » Tue, 2024-12-17 16:27 |
1 |
by Jamesavery22 Sat, 2025-01-04 19:32 |
|
|
Under-voltage fault with PMSM powered by bench supply by leheim » Fri, 2024-04-26 15:32 |
1 |
by electricfox Thu, 2024-05-02 10:19 |
|
|
Understanding FOC Wizard Innerworkings by gravity99 » Thu, 2022-08-18 22:24 |
2 |
by gravity99 Mon, 2022-08-22 15:23 |
|
|
Unrecognized USB port vesc tool 1.25 by geotoine » Fri, 2019-11-08 15:35 |
1 |
by bb67 Fri, 2020-06-12 18:10 |
|
|
Update 0.87 impossible by vpower » Thu, 2018-01-18 13:17 |
2 |
by arvidb Thu, 2018-01-18 17:07 |
|
|
Update fail from FW3.58 to 3.61 by sachs2019 » Tue, 2019-09-10 15:51 |
7 |
by AlmaRaposa Thu, 2021-03-11 17:44 |
|
|
Update FW on multiple VESC pcbs using CAN issue by Offline » Thu, 2021-05-20 07:36 |
0 |
by Offline Thu, 2021-05-20 07:36 |
|
|
Update FW using vesc tool over phone by SkaterBoy58 » Thu, 2019-03-14 05:33 |
0 |
by SkaterBoy58 Thu, 2019-03-14 05:33 |
|
|
Updated Firmware on 2 New VESC's says firmware doesnt match when connected by CanBus Cable by vesserik » Mon, 2019-04-08 21:10 |
1 |
by dbell Tue, 2020-12-01 02:14 |
|
|
Updating App and info xml failed by Pimousse » Tue, 2018-01-30 21:06 |
0 |
by Pimousse Tue, 2018-01-30 21:06 |
|
|
Upgrade the Bootloader? by erikfed » Tue, 2022-03-08 20:32 |
0 |
by erikfed Tue, 2022-03-08 20:32 |
|
|
Urgent Help Connecting TS5700N8501-like Magnetic Encoder by jumana » Tue, 2025-01-14 19:37 |
0 |
by jumana Tue, 2025-01-14 19:37 |
|
|
USB command and ADC1 Throttle by JWilson » Fri, 2024-08-09 23:24 |
1 |
by electricfox Sun, 2024-08-25 12:05 |
|
|
USB-serial_no ports show up at all by Josiah Eberharter » Tue, 2024-07-23 05:45 |
0 |
by Josiah Eberharter Tue, 2024-07-23 05:45 |
|
|
Use ADC2 as reverse button for ADC+UART/Current Reverse Button by jessejay356 » Mon, 2024-09-23 01:06 |
0 |
by jessejay356 Mon, 2024-09-23 01:06 |
|
|
Use sensors on the output shaft of a motor attached to a large gear ratio gearbox by davidq1688 » Wed, 2022-04-27 05:23 |
1 |
by tobiokanobi Thu, 2022-04-28 14:48 |
|
|
Use Vesc-Tool to run two motors simultaneously via CAN by microlomaniac » Thu, 2021-06-17 11:55 |
2 |
by spacewalker Tue, 2021-06-22 08:23 |
|
|
Values truncated, but why? by oger » Tue, 2020-03-24 17:43 |
0 |
by oger Tue, 2020-03-24 17:43 |
|
|
VECT Tool freezes after uploading lisp script by realphanta » Sun, 2025-07-27 17:05 |
2 |
by realphanta Thu, 2025-07-31 11:24 |
Log in to post new content in the forum.
