You are here
VESC Tool
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Is anyone else having the same problems by Jheckman » Mon, 2022-08-22 16:33 |
0 |
by Jheckman Mon, 2022-08-22 16:33 |
|
|
FSESC seems to be speed limiting my motor by 5amsung4 » Sat, 2022-09-03 18:50 |
0 |
by 5amsung4 Mon, 2022-09-05 07:51 |
|
|
Help i can not setup my motors by jakson01 » Fri, 2022-09-09 18:37 |
0 |
by jakson01 Fri, 2022-09-09 18:37 |
|
|
How to log events on a non bluetooth onewheel setup by carasta » Sat, 2023-05-13 22:01 |
0 |
by carasta Sat, 2023-05-13 22:01 |
|
|
HFI plot by Rick van der Sloot » Sun, 2022-10-02 22:26 |
0 |
by Rick van der Sloot Sun, 2022-10-02 22:26 |
|
|
Issue with Vesc Tool: MPU6050 IMU Not Detected After Power Cycling by Lennart Duijn » Thu, 2023-06-01 21:54 |
0 |
by Lennart Duijn Fri, 2023-06-02 09:03 |
|
|
Latched power switch on Trampa VESC 6 75A by dversity » Wed, 2023-06-28 00:36 |
0 |
by dversity Wed, 2023-06-28 00:36 |
|
|
Unable to connect to vesc through can bus by Kupofty » Thu, 2022-10-20 16:24 |
0 |
by Kupofty Thu, 2022-10-20 16:24 |
|
|
Power Monitor and Logging by IntDesign » Thu, 2023-07-06 18:08 |
0 |
by IntDesign Thu, 2023-07-06 18:08 |
|
|
Flipsky 6.6 and VESC 5.3 don't mix? by Miniproto » Sun, 2022-11-27 16:34 |
0 |
by Miniproto Sun, 2022-11-27 16:34 |
|
|
Previous versions of VESC Tool by Drosselmeier » Fri, 2023-07-14 12:49 |
0 |
by Drosselmeier Fri, 2023-07-14 12:49 |
|
|
Download for Windows VESC-Tool from FW5.02 era? by bmwman91 » Mon, 2023-07-24 02:03 |
0 |
by bmwman91 Mon, 2023-07-24 02:37 |
|
|
Motor not running after applying SINE/COSINE settings by DHOUT » Fri, 2023-01-27 03:32 |
0 |
by DHOUT Fri, 2023-01-27 03:32 |
|
|
duty cicle 95% but current not at max by rodrigo.baronio » Mon, 2023-02-06 15:52 |
0 |
by rodrigo.baronio Mon, 2023-02-06 15:52 |
|
|
One ESC two Motors by Vdca » Sat, 2023-09-23 20:24 |
0 |
by Vdca Sat, 2023-09-23 20:24 |
|
|
Noobs need to update and / or configure old VESC 4.12 by Loops » Tue, 2023-02-07 11:49 |
0 |
by Loops Tue, 2023-02-07 11:49 |
|
|
Balance App by EVolution EV » Tue, 2019-12-31 05:11 |
0 |
by EVolution EV Thu, 2020-01-02 05:55 |
|
|
VESC Tool for Android & GPS/GNSS sharing? by ahagge » Fri, 2021-10-01 05:04 |
0 |
by ahagge Fri, 2021-10-01 05:04 |
|
|
I need VESC Tool Version 1.13, please. by Astropower » Sun, 2019-09-08 18:22 |
0 |
by Astropower Sun, 2019-09-08 18:22 |
|
|
two motors one ppm for throttle and one for the direction? by Robby Ertmann » Wed, 2021-04-21 13:48 |
0 |
by Robby Ertmann Wed, 2021-04-21 13:48 |
|
|
no effect on set erpm/speed limit by xenon321 » Sat, 2021-04-24 20:43 |
0 |
by xenon321 Sun, 2021-04-25 16:53 |
|
|
Freewheeling by Stianaj » Fri, 2020-01-17 19:15 |
0 |
by Stianaj Fri, 2020-01-17 19:15 |
|
|
read RPM over CAN by nblange » Mon, 2021-05-03 20:43 |
0 |
by nblange Mon, 2021-05-03 20:43 |
|
|
one motor spinning faster than the other? by jon218white » Mon, 2020-12-14 22:57 |
0 |
by jon218white Mon, 2020-12-14 22:57 |
|
|
Update FW on multiple VESC pcbs using CAN issue by Offline » Thu, 2021-05-20 07:36 |
0 |
by Offline Thu, 2021-05-20 07:36 |
Log in to post new content in the forum.
