You are here
VESC Tool
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
questions about "RUN DETECTION" by yuri12 » Thu, 2022-01-20 04:30 |
0 |
by yuri12 Thu, 2022-01-20 04:30 |
|
|
The engine stopped spinning after updating firmware by brian adilman » Wed, 2022-01-26 17:40 |
0 |
by brian adilman Wed, 2022-01-26 19:15 |
|
|
NRF connection error by Denn » Wed, 2022-02-02 11:17 |
0 |
by Denn Wed, 2022-02-02 11:17 |
|
|
Throttle Input reading not changing by niko_la » Fri, 2022-07-22 02:40 |
0 |
by niko_la Fri, 2022-07-22 02:40 |
|
|
Different rpm when using 3 vesc with can-bus by ewakegermanyhq » Wed, 2022-08-03 17:03 |
0 |
by ewakegermanyhq Wed, 2022-08-03 17:03 |
|
|
Upgrade the Bootloader? by erikfed » Tue, 2022-03-08 20:32 |
0 |
by erikfed Tue, 2022-03-08 20:32 |
|
|
getting started by SilkyD » Mon, 2021-10-25 12:49 |
0 |
by SilkyD Mon, 2021-10-25 12:49 |
|
|
VESC Tool Device UI not shown on Raspberry Pi/Linux by Sebastiaan Koning » Mon, 2024-12-02 13:19 |
0 |
by Sebastiaan Koning Mon, 2024-12-02 13:19 |
|
|
Can I re-use an old Galaxy S3 to run the VESC tool? by Munkyheed » Fri, 2019-08-02 20:00 |
0 |
by Munkyheed Fri, 2019-08-02 20:00 |
|
|
lispBM command "gpio-hold" by Jamesavery22 » Sat, 2025-01-04 20:46 |
0 |
by Jamesavery22 Sat, 2025-01-04 20:46 |
|
|
Wrong Motor detection values after STM swap dual vesc 6 by Micro » Sun, 2019-08-18 01:59 |
0 |
by Micro Sun, 2019-08-18 02:14 |
|
|
Odys Alpha X3 Pro Settings by flashice » Mon, 2025-01-06 14:28 |
0 |
by flashice Mon, 2025-01-06 14:34 |
|
|
Update FW using vesc tool over phone by SkaterBoy58 » Thu, 2019-03-14 05:33 |
0 |
by SkaterBoy58 Thu, 2019-03-14 05:33 |
|
|
Inappropriate ioctl by Roger Wolff » Sat, 2018-06-02 17:38 |
0 |
by Roger Wolff Sat, 2018-06-02 18:04 |
|
|
Motor starting while flasing firmware by RSR » Sun, 2017-09-17 15:31 |
0 |
by RSR Sun, 2017-09-17 15:31 |
|
|
Incorrect parameter detection by macieksz@pro.onet.pl » Fri, 2019-08-30 16:05 |
0 |
by macieksz@pro.onet.pl Fri, 2019-08-30 16:05 |
|
|
Urgent Help Connecting TS5700N8501-like Magnetic Encoder by jumana » Tue, 2025-01-14 19:37 |
0 |
by jumana Tue, 2025-01-14 19:37 |
|
|
Vesc tool mobile for raspbian by Idoff » Sat, 2019-03-30 19:24 |
0 |
by Idoff Sat, 2019-03-30 19:24 |
|
|
How to activate e-brake on e-scooter with the throttle by Donatas Sukelis » Sat, 2019-04-27 10:09 |
0 |
by Donatas Sukelis Sat, 2019-04-27 10:09 |
|
|
Connecting ABI encoder to VESC by Gas_Sn4ke » Mon, 2018-11-26 06:00 |
0 |
by Gas_Sn4ke Mon, 2018-11-26 06:00 |
|
|
Problem with encoder readings with arduino by ruthvikchanda » Thu, 2018-12-06 07:06 |
0 |
by ruthvikchanda Thu, 2018-12-06 07:06 |
|
|
Motor detection failed/ 0 faults by jnweb29 » Sat, 2017-12-23 21:07 |
0 |
by jnweb29 Sat, 2017-12-23 21:07 |
|
|
ADC Positive and Negative Ramping Time - not working by Astropower » Tue, 2019-05-28 22:41 |
0 |
by Astropower Tue, 2019-05-28 22:41 |
|
|
Updating App and info xml failed by Pimousse » Tue, 2018-01-30 21:06 |
0 |
by Pimousse Tue, 2018-01-30 21:06 |
|
|
Reverse gear is engaged when power is lost by simDen » Mon, 2024-09-30 13:18 |
0 |
by simDen Mon, 2024-09-30 13:18 |
Log in to post new content in the forum.
