You are here
VESC Tool
Log in to post new content in the forum.
Topic / Topic starter | Replies |
Last post![]() |
|
---|---|---|---|
PPM read has an offset by tuloski » Thu, 2018-09-13 09:38 |
2 |
by Stupidspencer Fri, 2019-07-19 03:09 |
|
Fault Codes by Joe_Lowtech » Wed, 2019-02-13 20:06 |
2 |
by mthielvoldt Thu, 2019-07-18 00:38 |
|
Parametre for Low RPM Limit by ilan248@gmail.com » Wed, 2019-07-10 11:01 |
1 |
by askker Thu, 2019-07-11 05:04 |
|
cant connect via usb by curtm » Wed, 2019-06-19 03:05 |
2 |
by curtm Thu, 2019-07-04 00:37 |
|
UART write read arduino by matiller » Sat, 2019-06-01 20:18 |
0 |
by matiller Sat, 2019-06-01 20:18 |
|
ADC Positive and Negative Ramping Time - not working by Astropower » Tue, 2019-05-28 22:41 |
0 |
by Astropower Tue, 2019-05-28 22:41 |
|
VESC Tool Error by Geir Henriksen » Fri, 2019-05-10 14:55 |
1 |
by Geir Henriksen Fri, 2019-05-10 15:18 |
|
Multiple VESC's in duty cycle mode by Rudolf10000 » Sat, 2019-04-20 13:24 |
1 |
by Rudolf10000 Mon, 2019-04-29 19:34 |
|
How to activate e-brake on e-scooter with the throttle by Donatas Sukelis » Sat, 2019-04-27 10:09 |
0 |
by Donatas Sukelis Sat, 2019-04-27 10:09 |
|
Vesc tool mobile for raspbian by Idoff » Sat, 2019-03-30 19:24 |
0 |
by Idoff Sat, 2019-03-30 19:24 |
|
Setup parameters for battery in VESC Tool by Ulrich » Tue, 2019-02-26 11:47 |
3 |
by Photolad61 Wed, 2019-03-27 17:26 |
|
Vesc-Tool mobile on Play Store. by frank » Fri, 2019-02-15 19:54 |
11 |
by Boesila Mon, 2019-03-25 20:28 |
|
BEMF plot not working with VESC6 by ESCam » Tue, 2019-03-12 21:29 |
2 |
by ESCam Tue, 2019-03-19 18:03 |
|
Connection over USB failed by sangious » Sun, 2019-03-17 01:20 |
0 |
by sangious Sun, 2019-03-17 01:20 |
|
Update FW using vesc tool over phone by SkaterBoy58 » Thu, 2019-03-14 05:33 |
0 |
by SkaterBoy58 Thu, 2019-03-14 05:33 |
|
[SOLVED] RPM setting not working by olivierskypullc... » Wed, 2019-02-27 12:14 |
2 |
by olivierskypullc... Wed, 2019-03-06 10:10 |
|
Vesc Tool not opening on windows computer by maccert » Sat, 2019-03-02 11:04 |
2 |
by Luca Torani Sun, 2019-03-03 20:32 |
|
Trying to connect over USB, but new 6.4 connects and disconnects a few seconds later. by MaxMaker1 » Thu, 2018-05-24 16:15 |
12 |
by frank Thu, 2019-02-21 20:34 |
|
setting up development environment for android by jaghori.sasan » Wed, 2019-02-20 14:59 |
0 |
by jaghori.sasan Wed, 2019-02-20 14:59 |
|
Flipsky nrf51288 by Idoff » Tue, 2018-12-11 21:33 |
2 |
by frank Mon, 2019-02-18 09:00 |
|
Advanced settings for FOC motor detection (flux linkage) by jaghori.sasan » Sun, 2019-02-17 09:34 |
2 |
by jaghori.sasan Sun, 2019-02-17 17:51 |
|
Sudden vesc unresponsiveness by nolander » Mon, 2019-01-07 22:29 |
6 |
by Caustic_Zinc Mon, 2019-02-11 09:32 |
|
Is there a complete documentation for the communication protocol between the vesc tool and the board? by aishangmu » Tue, 2018-12-25 09:00 |
2 |
by Caustic_Zinc Fri, 2019-02-08 19:27 |
|
Sensored FOC not working by Jarson » Thu, 2019-01-24 20:03 |
1 |
by Caustic_Zinc Fri, 2019-02-08 19:19 |
|
Adjusting Beta Value for Motor Thermistor. by Ecyclist » Thu, 2018-12-06 23:22 |
12 |
by Ecyclist Tue, 2019-01-29 04:29 |
Log in to post new content in the forum.
