You are here

VESC Tool

Topic / Topic startersort descending Replies Last post
Normal topic Setup FOC automaticly without vesc tool ihm
by NATUITION » Tue, 2024-04-16 10:11
0
by NATUITION
Tue, 2024-04-16 10:11
Normal topic Setup for very slow < 100RPM on Maytech 6365 Motor.
by jason3w » Tue, 2020-09-01 10:52
2
by asapereira
Mon, 2020-09-14 10:26
Normal topic Setup motor foc
by Vincent LAMBERT » Thu, 2022-02-03 12:22
0
by Vincent LAMBERT
Thu, 2022-02-03 12:22
Normal topic Setup parameters for battery in VESC Tool
by Ulrich » Tue, 2019-02-26 11:47
3
by Photolad61
Wed, 2019-03-27 17:26
Normal topic Several questions and safe values
by miskuhunor@gmail.com » Thu, 2021-09-09 08:33
0
by miskuhunor@gmail.com
Thu, 2021-09-09 08:33
Normal topic sick srm50 absolute encoder, I don't know how to configure it
by Davidson SIlvei... » Mon, 2024-04-22 21:45
0
by Davidson SIlvei...
Mon, 2024-04-22 21:45
Normal topic single VESC 6+ controlled by CAN-bus
by vinci » Fri, 2021-07-09 15:42
1
by yuri12
Wed, 2022-02-09 17:23
Normal topic Smart Reverse Minimum Erpm
by ZenRides » Wed, 2022-02-16 05:36
4
by nabil sassi
Tue, 2022-04-12 23:21
Normal topic Software safety features interrupting normal operation.
by Tsomo » Wed, 2021-07-14 01:29
2
by Tsomo
Wed, 2021-07-14 01:32
Normal topic Speed control
by dent » Tue, 2020-03-10 20:11
2
by dent
Wed, 2020-03-11 02:49
Normal topic Startup codes?
by anthonys » Sat, 2021-06-19 17:29
0
by anthonys
Sat, 2021-06-19 17:29
Normal topic STM32F405RGTx LQFP64 .ioc file
by gyongyoj » Fri, 2023-10-27 14:20
0
by gyongyoj
Fri, 2023-10-27 14:20
Normal topic Sudden vesc unresponsiveness
by nolander » Mon, 2019-01-07 22:29
6
by Caustic_Zinc
Mon, 2019-02-11 09:32
Normal topic supported firmware
by velolac » Mon, 2020-01-13 22:55
3
by velolac
Tue, 2020-01-14 21:47
Normal topic Switch between different modes via remote
by Cledus » Sun, 2017-10-22 13:56
2
by MatwoSvK
Tue, 2017-11-07 22:32
Normal topic Taking 5-6 seconds for running motor under ADC mode
by asnamp » Fri, 2022-06-24 13:02
1
by skyline1970
Thu, 2022-11-24 21:24
Normal topic Terminal Command for Current?
by Mannerow » Thu, 2020-10-29 23:07
0
by Mannerow
Thu, 2020-10-29 23:07
Normal topic terminal command via UART for a gimbal
by fredfred » Sat, 2021-12-18 20:49
0
by fredfred
Sat, 2021-12-18 20:49
Normal topic The engine stopped spinning after updating firmware
by brian adilman » Wed, 2022-01-26 17:40
0
by brian adilman
Wed, 2022-01-26 19:15
Normal topic Throttle and Brake
by shatty » Wed, 2021-03-10 01:19
0
by shatty
Wed, 2021-03-10 01:22
Normal topic Throttle Input reading not changing
by niko_la » Fri, 2022-07-22 02:40
0
by niko_la
Fri, 2022-07-22 02:40
Normal topic throttle mapping: non-zero current at zero adc input?
by FreddyForLaunch » Wed, 2021-04-14 21:48
0
by FreddyForLaunch
Thu, 2021-04-15 09:00
Normal topic Throttle movement
by Lasse » Tue, 2023-03-07 12:16
0
by Lasse
Tue, 2023-03-07 12:16
Normal topic Tool for OSX MAC
by oger » Wed, 2020-03-25 17:21
0
by oger
Wed, 2020-03-25 17:21
Normal topic Trasmitter not able to communicate with VESC
by Andrea » Thu, 2020-03-26 20:22
1
by TheFallen
Mon, 2020-12-28 16:16
New posts
No new posts
Hot topic with new posts
Hot topic without new posts
Sticky topic
Locked topic
Subscribe to RSS - VESC Tool