You are here
VESC Tool
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
VESC 4.12 - Current limited at 100A by Laerson » Sun, 2019-09-08 20:23 |
1 |
by benjamin Mon, 2019-09-09 18:20 |
|
|
VESC tool 0.94 needed(Linux) by tahirhasan » Wed, 2019-09-11 16:34 |
1 |
by mustafa Sun, 2019-11-10 20:34 |
|
|
Compiled Vesc Tool Won't Recognize Firmware - Windows 1.23 by KingRagnar22 » Wed, 2019-10-02 01:29 |
1 |
by a.dahhak Mon, 2021-02-01 16:54 |
|
|
auxiliary output mode? by shaman » Thu, 2020-02-20 01:23 |
1 |
by skyline1970 Mon, 2021-02-01 21:07 |
|
|
Motor RPM counter in Dashboard and Mob App by Rex » Fri, 2022-06-17 07:01 |
0 |
by Rex Fri, 2022-06-17 07:01 |
|
|
Auto tune pid by vcth » Mon, 2022-06-27 18:52 |
0 |
by vcth Mon, 2022-06-27 18:52 |
|
|
current of holding by reff » Thu, 2022-01-27 16:38 |
0 |
by reff Thu, 2022-01-27 16:39 |
|
|
Setup motor foc by Vincent LAMBERT » Thu, 2022-02-03 12:22 |
0 |
by Vincent LAMBERT Thu, 2022-02-03 12:22 |
|
|
Bluetooth connection UUID issue-how to find it? by pistolriver » Thu, 2022-07-21 00:53 |
0 |
by pistolriver Thu, 2022-07-21 00:53 |
|
|
how to communication with arduino on vesc via CAN by yuri12 » Tue, 2022-02-08 13:16 |
0 |
by yuri12 Tue, 2022-02-08 13:16 |
|
|
How to read the CAN message with CAN anlayzer by yuri12 » Thu, 2022-03-03 18:21 |
0 |
by yuri12 Thu, 2022-03-03 18:21 |
|
|
VESC Tool app min hardware requirements by flix » Sat, 2022-04-16 22:13 |
0 |
by flix Sat, 2022-04-16 22:13 |
|
|
VESC Tool speed control overshoot by PKmita » Tue, 2022-04-26 16:05 |
0 |
by PKmita Tue, 2022-04-26 16:12 |
|
|
Logging set values to csv file by jukawt » Mon, 2021-12-06 14:57 |
0 |
by jukawt Mon, 2021-12-06 14:57 |
|
|
App. settings: "Enable servo output on PPM-port when PPM-app is disabled." option by alexantosh » Fri, 2021-12-10 09:46 |
0 |
by alexantosh Fri, 2021-12-10 09:46 |
|
|
terminal command via UART for a gimbal by fredfred » Sat, 2021-12-18 20:49 |
0 |
by fredfred Sat, 2021-12-18 20:49 |
|
|
Issues with VESC 75/300 and VESC-Tool V3.01 by hpb66 » Fri, 2022-06-03 09:15 |
0 |
by hpb66 Fri, 2022-06-03 09:15 |
|
|
Minimum System Requirements for VESC Tool 3.01 under Windows by j.konrad » Mon, 2022-01-24 21:48 |
0 |
by j.konrad Mon, 2022-01-24 21:48 |
|
|
UI problem by Zeos » Fri, 2026-01-30 11:29 |
0 |
by Zeos Fri, 2026-01-30 11:29 |
|
|
Vesc tool ver 3.00 source code by galihatmojo » Thu, 2025-02-20 01:38 |
0 |
by galihatmojo Thu, 2025-02-20 01:38 |
|
|
VESC QML Documentation by bzucak » Tue, 2025-03-25 21:11 |
0 |
by bzucak Tue, 2025-03-25 21:11 |
|
|
Bug? by arxera » Sat, 2026-04-04 12:34 |
0 |
by arxera Sat, 2026-04-04 12:34 |
|
|
Help with more torque with vesc by Juzy » Wed, 2025-04-02 04:52 |
0 |
by Juzy Wed, 2025-04-02 06:59 |
|
|
Bimodal Ld-Lq Saliency on T Motor AT4130 by ohceejay » Wed, 2026-04-15 18:30 |
0 |
by ohceejay Wed, 2026-04-15 18:30 |
|
|
Bug found in VESC tool 6.05 related to VESC BMS by f.damien12 » Wed, 2025-04-09 17:11 |
0 |
by f.damien12 Wed, 2025-04-09 17:13 |
Log in to post new content in the forum.
